Abasszadeh, Yaghoob Dynamic analysis of three-cylinder engine with balancing shaft [Volume 60, Issue 60, 2020, Pages 61-75]
Abbasi, M. Design of Nondestructive System for Hardness of Carbonitrided Steel Parts âUsing Eddy Current Testing Method: Case study on the Tappet Parts [Volume 52, Issue 52, 2018, Pages 19-28]
Abbaszadeh, Yaghoub Simulation of torsional vibrations of dual mass flywheel in a 3-cylinder engine [Volume 70, Issue 1, 2023, Pages 1-13]
Abdi Aghdam, E The Effect Of Burned Residual Gases On Gasoline-NG Dual-Fuel Engine Combustion Performance With Skip-Fire Technique [Volume 63, Issue 63, 2021, Pages 3-11]
Abdi Aghdam, E. Experimental study on effect of cycle-to-cycle variability on HC emission in a SI engine [Volume 33, Issue 33, 2014, Pages 23-30]
Abdi Aghdam, E. Study of the performance in dual fuels 50% gasoline -50% NG and single original fuels and comparison in part load [Volume 52, Issue 52, 2018, Pages 11-18]
Abdi Aghdam, Ebrahim The Effect of Burned Residual Gases on Optimum Ignition Timing using Skip Fire Technique [Volume 50, Issue 50, 2018, Pages 67-75]
Abdi Aghdam, Ebrahim Simulating and Validating a multi-zone thermodynamic-model for gasoline-NG dual-fuel SI engines and predicting NO emission [Volume 67, Issue 67, 2022, Pages 3-15]
Abdi Aghdam, Ebrahim An experimental study of determining friction force between ring and cylinder by measuring piston movement [Volume 71, Issue 2, 2024, Pages 40-54]
Abdi Aghdam, Ebrahim The output performance of the 25% gasoline-75% NG combination mode and its comparison with NG mode [Volume 71, Issue 1, 2024, Pages 40-51]
Abdi Aghdam, Ebrahim Measuring the mass of fuel injected into the engine cycle by introducing a gas pressure fueling system [(Articles in Press)]
Abdolmaleki, S. Investigation of diesel fuel and soybean methyl esters emission in high-speed diesel engine [Volume 35, Issue 35, 2014, Pages 31-39]
Abdolmaleki, S. Thermal analysis of multiple layers steel(MLS) cylinder head gasket via test [Volume 48, Issue 48, 2017, Pages 19-26]
Abdolmaleki, S. Energy balance on a three-cylinder engine with turbocharger [Volume 49, Issue 49, 2018, Pages 29-38]
Abdolmaleki, Saeed Comparison of Aged and fresh Automotive Three-Way Catalyst in Driving Cycle [Volume 57, Issue 57, 2020, Pages 75-83]
Abdolmaleki, Saeed Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Abdul Aziz, A. The effect of ethanol combustion on HCCI engine performance and emissions [Volume 41, Issue 41, 2016, Pages 21-30]
Abdullah, A. Experimental investigation of the effect of pressure and density ratio on the gaseous spray of the group-hole nozzle [Volume 28, Issue 28, 2012, Pages 11-19]
Abdullah, A. Sensitivity analysis of parameters affecting image processing of high pressure gaseous jet images [Volume 33, Issue 33, 2014, Pages 43-52]
Abedi, A Numerical and Experimental Analysis of Flow Velocity in the Cylinder Head of Transparent Iranian National Engine with PIV Method [Volume 63, Issue 63, 2021, Pages 61-76]
Abedi, M. J Emissions and fuel consumption reduction of the OM355 diesel engine using a common rail fuel injection and selective catalytic reduction systems [Volume 62, Issue 62, 2021, Pages 15-21]
Abedi, Reza Experimental and Analytical Investigation of the Oil Viscosity Effect on Vertical Vibrations of a CI Engine [Volume 46, Issue 46, 2017, Pages 65-74]
Abolhassani, S. Failure Analysis of a Four Cylinder Diesel Engine Crankshaft Made From Nodular Cast Iron [Volume 22, Issue 22, 2011, Pages 21-28]
Adamieyan, A. Thermal Analysis of Turbocharger Steel Gasket via Experimental Test [Volume 53, Issue 53, 2019, Pages 33-44]
Adeli, Amir Hossein Study of the effect of nanoparticles on thermophysical properties and rheological behavior of cooling fluid in combustion engines [Volume 70, Issue 3, 2023, Pages 1-17]
Adine beigi, mohammad Numerical investigation of the effect of a turbocharger compressor blades angle on its performance [Volume 45, Issue 45, 2017, Pages 63-76]
Adnani, S.A. The initial estimate of the useful life of the oil in diesel engines using oil analysis [Volume 25, Issue 25, 2012, Pages 45-55]
Afarid, MohammadJavad Experimental investigation of the effect of changing elements in the cylinder liner of BMP1 diesel engine on surface hardness [Volume 72, Issue 1, 2025, Pages 25-34]
Afrand, Masoud Numerical Simulation Effect of EHC on CO Emission in Cold-Start Conditions of a Motorcycle Engine [Volume 44, Issue 44, 2016, Pages 43-52]
Afshari, E. Performance Analysis of a Polymer Electrolyte Fuel Cell System for Automotive Application [Volume 16, Issue 16, 2009, Pages 3-15]
Afshari, M. Study of spark ignition engine emissions fueled by blended hydrogen and methane [Volume 31, Issue 31, 2013, Pages 55-63]
Afshari, Mehrdad A model for estimation of wear of engine rings based on the amount of blowby and oil consumption in durability tests [Volume 71, Issue 1, 2024, Pages 67-78]
Aghahasani, Mahdi Investigating the influence of injection timing on the performance of a RCCI engine [Volume 70, Issue 1, 2023, Pages 91-105]
Agha Mirsalim, Mostafa Experimental study of the diesel injector nozzle sediment effect on fuel spray behavior [Volume 54, Issue 54, 2019, Pages 13-23]
Agha Mirsalim, S. M. A novel experimental test rig for simulating of the fuel injection system components behavior under cold conditions [Volume 47, Issue 47, 2017, Pages 31-38]
Agha Mirsalim, S. M. Study of two-stage turbocharging for compensation of low-end torque [Volume 49, Issue 49, 2018, Pages 39-46]
Agha Mirsalim, S. M. Principle of valves timing optimization in D87 diesel to premixed natural gas engine conversion [Volume 49, Issue 49, 2018, Pages 65-76]
Agha Mirsalim, S. Mostafa The Thermal Simulation of an Exhaust Valve and its Seat Using Thermal Contact Conductance Obtained from the Inverse Solution [Volume 36, Issue 36, 2014, Pages 27-38]
Aghanajafi, C. Simulation of Heat Transfer in the Cooling Passages of the âEF7â Engine Considering Boiling Phenomenon [Volume 19, Issue 19, 2010, Pages 64-73]
Aghdam, E. A. Experimental study of a spark ignition single-cylinder research engine exhaust emissions in gasoline and natural gas fuel cases [Volume 39, Issue 39, 2015, Pages 49-55]
Aghkhani, Mohammad Hossein Evaluation of reliability of diesel engine connecting rod by accelerated test method [Volume 64, Issue 64, 2021, Pages 41-53]
Agkhani, Mohammad Hossein Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Ahmadi, H. Condition Monitoring of Diesel Engine via Oil Analysis Using Fuzzy Logic [Volume 19, Issue 19, 2010, Pages 9-18]
Ahmadi, H. Effects of Nano-Particles on Properties of Engine Oil and its Functionality Rate on Wear Reduction [Volume 24, Issue 24, 2011, Pages 3-12]
Ahmadi, H. Optimization of performance in tractor engine with biodiesel-ethanol-diesel fuels using response surface methodology [Volume 29, Issue 29, 2013, Pages 15-24]
Ahmadi, M. Investigation of Friction Phenomena by Using Acoustic Emission Method [Volume 19, Issue 19, 2010, Pages 1-8]
Ahmadi, M. Investigation on the Effect of the Cooling Jet Impacts on the Moving Piston on Produced Oil Droplets Using a Motored Engine [Volume 19, Issue 19, 2010, Pages 38-48]
Ahmadi, M. Experimental investigation on the pumping loss and pressure oscillations in the crankcase [Volume 23, Issue 23, 2011, Pages 3-10]
Ajami, Nima Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Ajami, Nima CFD simulation of wall film during fuel injection and combustion in a three-cylinder turbocharged gasoline direct injection engine [Volume 70, Issue 4, 2024, Pages 1-13]
Ajami Kashani, Nima Conceptual and experimental study of an Atkinson cycle engine of a Series-Parallel hybrid electric vehicle [Volume 70, Issue 4, 2024, Pages 69-80]
Akbari, M. Using predictive combustion model in combustion modeling of cooled EGR turbocharged engine [Volume 25, Issue 25, 2012, Pages 57-67]
Akbari, Rahman Dynamic analysis of three-cylinder engine with balancing shaft [Volume 60, Issue 60, 2020, Pages 61-75]
Akbari, S. Controlling natural gas combustion timing in HCCI engine with synthetic gas enrichment using a chemical kinetic model [Volume 32, Issue 32, 2013, Pages 13-20]
Akbarpouran Khayati, E Emissions and fuel consumption reduction of the OM355 diesel engine using a common rail fuel injection and selective catalytic reduction systems [Volume 62, Issue 62, 2021, Pages 15-21]
Akbarpouran Khayati, Ebrahim Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Akbarpouran Khayati, Ebrahim Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Akhlaghi, M. Investigation of effect of adding natural gas on gasoline laminar flame speed [Volume 32, Issue 32, 2013, Pages 49-57]
Akhlaghi, M. Laminar flame speed measurement and correlation for methane-iso-octane fuel blend [Volume 39, Issue 39, 2015, Pages 11-20]
Akhlaghi, M. An experimental investigation of the influence of diluent gas on laminar flame speed of natural gas and gasoline fuel mixture [Volume 40, Issue 40, 2015, Pages 47-57]
Akhtardanesh, Mohammad Ali Acoustic extintion of partially premixed counterflow flame [Volume 70, Issue 3, 2023, Pages 39-52]
Alasti, A. Nonlinear Oxygen Sensor Output Voltage Estimation in a Gasoline Engine Using NARX Model [Volume 22, Issue 22, 2011, Pages 13-20]
Alasty, A. Steady-state modeling of a turbocharger in gasoline engines [Volume 26, Issue 26, 2012, Pages 21-30]
Alaviyoun, S. Experimental investigation on the pumping loss and pressure oscillations in the crankcase [Volume 23, Issue 23, 2011, Pages 3-10]
Alaviyoun, Sh. Performance study of a diaphragm type crankcase pressure control valve [Volume 30, Issue 30, 2013, Pages 47-54]
Alaviyoun, ُShahabeddin Thermal Investigation of turbocharger using infra-red camera [Volume 50, Issue 50, 2018, Pages 3-16]
Alaviyoun, S.S. Investigation of Effects of Spark Plugâs Electrodes Erosion on the Required Ignition Voltage and Performance of Natural Gas Engine [Volume 21, Issue 21, 2011, Pages 21-34]
Alaviyoun, S.S. Effect of electrode erosion on the required ignition voltage of spark plug in CNG spark ignition engine [Volume 26, Issue 26, 2012, Pages 31-39]
Aldarvish, Zoheir Evaluation of Performance and Vibration of a Diesel Engine Using Ag Nanoparticles Added to Diesel and Biodiesel Fuel Blends [Volume 46, Issue 46, 2017, Pages 15-26]
Aliasghari, P. Effect of Crossing Diesel Fleet in Tehran on Black Carbon Air Pollution [Volume 49, Issue 49, 2018, Pages 19-28]
Alijani, Navid Mass Properties Identification of a Rigid Body Using Modal Analysis [Volume 68, Issue 68, 2022, Pages 49-55]
Alinejad, Javad Investigation of parameters influencing production rate and power consumption in Cut-Wire process for shot peening of automotive springs [Volume 72, Issue 2, 2025, Pages 31-42]
Aliramezani, M. Prediction of charge effect on SI engine performance for hydrocarbon fuels [Volume 25, Issue 25, 2012, Pages 25-34]
Aliramezani, M. Effect of hydrogen mole fraction and air-fuel distribution of hydrogen-methane blend on SI engine performance [Volume 27, Issue 27, 2012, Pages 23-31]
Aliyari-Shoorehdeli, Mahdi Convolutional transformer approach for engine spark plug fault diagnosis using acoustic signal [Volume 70, Issue 4, 2024, Pages 56-68]
Alizadeh, D. Condition Monitoring of Diesel Engine via Oil Analysis Using Fuzzy Logic [Volume 19, Issue 19, 2010, Pages 9-18]
Alizadeh, Hossien Performance and Emissions of a Tractor engine operating on biodiesel-diesel blends with EGR [Volume 42, Issue 42, 2016, Pages 13-22]
Alizadeh, M. Effect of combustion products of gasoline-ethanol blended fuel on corrosion of valve and cylinder head alloys of SI engines [Volume 28, Issue 28, 2012, Pages 3-10]
Alizadehnia, S Improving identification of combustion engine to use in model-based calibration [Volume 63, Issue 63, 2021, Pages 23-34]
Alizadehnia, S. Dynamic-Thermodynamic Mathematical Model of Stirling Engine to Improve Efficiency and Power [Volume 23, Issue 23, 2011, Pages 72-85]
Alizadehnia, S. A novel experimental test rig for simulating of the fuel injection system components behavior under cold conditions [Volume 47, Issue 47, 2017, Pages 31-38]
Alizadehnia, S. EF7 engine flywheel bolted joint design improvement by theoretical and experimental investigations [Volume 48, Issue 48, 2017, Pages 27-40]
Alizadehnia, Siamak Analyzing driving behavior for fuel efficiency using ECU data based on artificial intelligence [Volume 71, Issue 1, 2024, Pages 1-15]
Alizadenia, S. Prediction Oil Parameter of Connecting Rod Small End Bearing of EF7 Engine by Using Artificial Neural Network by Simulation in AVL Excite Software [Volume 20, Issue 20, 2010, Pages 22-29]
Allocca, Luigi Air-fuel Mixture Preparation for Internal Combustion Engines:Optical Techniques for Diagnosis of the Spray Developments [Volume 57, Issue 57, 2020, Pages 51-64]
Allocca, Luigi Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
Allocca, Luigi Characterization of High-pressure Hydrogen Jet for ICE in terms of Morphology and Flow-rates [Volume 70, Issue 4, 2024, Pages 27-39]
Almansoori, A. Q. A novel experimental test rig for simulating of the fuel injection system components behavior under cold conditions [Volume 47, Issue 47, 2017, Pages 31-38]
Altafi, Davood Investigation of the Effect of the Geometric Deviations on the Performance of a Radial Flow Compressor Employing Uncertainty Quantification (UQ) and Sensitivity Analysis [Volume 67, Issue 67, 2022, Pages 51-63]
Amani, E. Energy balance on a three-cylinder engine with turbocharger [Volume 49, Issue 49, 2018, Pages 29-38]
Aminian, Emad Developing a reduced chemical kinetic mechanism for natural gas/biodiesel mixture combustion [Volume 71, Issue 4, 2025, Pages 15-32]
Amirmazlaghani, Maryam Analyzing driving behavior for fuel efficiency using ECU data based on artificial intelligence [Volume 71, Issue 1, 2024, Pages 1-15]
Amirmazlaghani, Mohammad Barbod Analyzing driving behavior for fuel efficiency using ECU data based on artificial intelligence [Volume 71, Issue 1, 2024, Pages 1-15]
Amirpour Molla, M. A Study on Noise Transmission Loss (TL) Through Duct of Air Intake System of Engine with Porous Insulator Considering Statistical Energy Analysis Method [Volume 19, Issue 19, 2010, Pages 29-37]
Amjadi, Morteza Developing a virtual reality simulator for skill enhancement; case study: the assembly process of the EF7 national engine's timing belt [Volume 72, Issue 2, 2025, Pages 43-55]
Aravand, Arash Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Aravand, Arash Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Arbabiyan, Kourosh Utilization of internal heat exchanger in air condition pipe at automotive industry [Volume 72, Issue 2, 2025, Pages 1-8]
Arbab Tafti, Mohammadreza Simulation of fuel consumption of a hydrogen fuel cell electric vehicle with a thermostat control strategy and variables affecting its fuel consumption in ADVISOR software [Volume 72, Issue 3, 2025, Pages 85-105]
Arjangnia, A. Experimental Investigation of the EGR Temperature Effects on the Destruction of the Fuelâs Availability Due to Combustion Processes in IDI Diesel Engine Cylinder [Volume 22, Issue 22, 2011, Pages 62-68]
Armin, Mahbod Operating Range Expansion in a HCCI Natural Gas Engine Using Charge and Thermal Stratification in Combustion Chamber [Volume 54, Issue 54, 2019, Pages 51-63]
Asadi, Alireza Investigating the effects of geographics climate on the characteristics of statistical data and driving cycle [Volume 70, Issue 2, 2023, Pages 37-65]
Asadi, M. Effect of starting temperature and belt width on lateral force of timing belt [Volume 48, Issue 48, 2017, Pages 13-18]
Asadi, M. An investigation on the effects of camshaft surface defects on producing high-frequency noises in internal combustion engines [Volume 52, Issue 52, 2018, Pages 3-10]
Asadi Asad Abad, Mohammad Reza Detection and classification of mechanical faults of an engine alternator based on vibration signals and frequency analysis [Volume 61, Issue 61, 2021, Pages 3-10]
Asadi_Moghaddam, Bahareh Concept selection for engine components using the DEMATEL-ANP-TOPSIS combination method: case study for cam bearing frame part [Volume 61, Issue 61, 2021, Pages 61-71]
Asadi Taheri, M. EF7 engine flywheel bolted joint design improvement by theoretical and experimental investigations [Volume 48, Issue 48, 2017, Pages 27-40]
Asadi Taheri, Mohsen The process of vehicle engine development at IPCO [Volume 64, Issue 64, 2021, Pages 3-11]
Asef, Ali Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Asef, Ali Conceptual and experimental study of an Atkinson cycle engine of a Series-Parallel hybrid electric vehicle [Volume 70, Issue 4, 2024, Pages 69-80]
Asgari, Tahmoreth Development of balance shaft and flywheel for single cylinder diesel engine based on analytical approach and comparison with the simulation result [Volume 51, Issue 51, 2018, Pages 63-74]
Ashari, E. Simulating and prototyping of a compression ring for diesel engine regarding required spring back force [Volume 32, Issue 32, 2013, Pages 21-28]
Ashouri, Hojjat Evaluation of temperature effect on modal analysis for exhaust manifold [Volume 61, Issue 61, 2021, Pages 11-21]
Ashouri, Hojjat Effect of perimeter fins in low cycle fatigue for exhaust manifold [Volume 61, Issue 61, 2021, Pages 23-34]
Ashouri, Hojjat Low cycle fatigue life analysis for exhaust manifold considering Elastoviscoplastic effect [Volume 70, Issue 2, 2023, Pages 22-36]
Ashouri, Hojjat Thermo-mechanical fatigue life prediction for exhaust manifold based on Sehitoglu model considering oxidation and creeping damages [Volume 71, Issue 4, 2025, Pages 1-14]
Ashouri, Hojjat The effect of changing fuel from gasoline to compressed natural gas on the high cycle fatigue life of M13 engine piston [Volume 72, Issue 3, 2025, Pages 106-123]
Ashrafi, Khosro Role of passenger cars and taxies in air pollution of Tehran, Iran [Volume 69, Issue 69, 2022, Pages 21-29]
Askary Moghadam, R. Dynamic-Thermodynamic Mathematical Model of Stirling Engine to Improve Efficiency and Power [Volume 23, Issue 23, 2011, Pages 72-85]
Aslani, A.R. Experimental and numerical investigation of stress in engine crankshaft [Volume 32, Issue 32, 2013, Pages 29-36]
Ataee Tarzanagh, Majid The Effect of Burned Residual Gases on Optimum Ignition Timing using Skip Fire Technique [Volume 50, Issue 50, 2018, Pages 67-75]
Ataee Tarzanagh, Majid The output performance of the 25% gasoline-75% NG combination mode and its comparison with NG mode [Volume 71, Issue 1, 2024, Pages 40-51]
Ataee Tarzanagh, Majid Measuring the mass of fuel injected into the engine cycle by introducing a gas pressure fueling system [(Articles in Press)]
Ataripour, Mohammadreza Prediction and Comparison of the Effect of N-butanol and Ethanol Addition to the Biodiesel-diesel Fuel Mixture on the Performance and Emissions Characteristics of a Diesel Engine [Volume 64, Issue 64, 2021, Pages 28-40]
Auriemma, M. Fluid Dynamics Investigation of a GDI Fuel Spray by Particle Image Velocimetry [Volume 14, Issue 14, 2009, Pages 19-26]
Ayatollahi, M. Thermo-Mechanical Fatigue Life Assessment of Diesel Engine Hot Components [Volume 23, Issue 23, 2011, Pages 59-71]
Azadi, M. An Investigation of High Cycle Fatigue Behavior of Magnesium Alloy for Cylinder Head Application [Volume 24, Issue 24, 2011, Pages 29-35]
Azadi, M. Failure analysis of an intake valve in a gasoline engine [Volume 26, Issue 26, 2012, Pages 3-9]
Azadi, M. Coating thickness effect on stress distribution of coated cylinder head considering residual stress [Volume 26, Issue 26, 2012, Pages 49-57]
Azadi, M. Low cycle fatigue analysis of magnesium alloy cylinder head based on plastic strain energy approach [Volume 27, Issue 27, 2012, Pages 3-10]
Azadi, M. Finite element analysis of thermal and mechanical stresses in diesel engine cylinder head using two-layer elastic-viscoplastic model [Volume 28, Issue 28, 2012, Pages 51-60]
Azadi, M. Failure analysis of a dynamometer drive shaft coupled to an engine [Volume 30, Issue 30, 2013, Pages 37-46]
Azadi, M. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Azadi, M. Evaluation of continuum damage at different temperatures for aluminum-silicon alloy of engine piston within low-cycle fatigue regime [Volume 52, Issue 52, 2018, Pages 43-54]
Azadi, Mahboobeh Optimization of solution temperature and time in nickel-based super-alloy of engine turbo-charger based on hardness by design of experiments [Volume 43, Issue 43, 2016, Pages 63-70]
Azadi, Mohammad Optimization of solution temperature and time in nickel-based super-alloy of engine turbo-charger based on hardness by design of experiments [Volume 43, Issue 43, 2016, Pages 63-70]
Azadi, Mohammad Ratcheting crystal plasticity modeling in microstructure of magnesium alloy under stress-controlled cyclic tensile loading with non-zero mean stress [Volume 68, Issue 68, 2022, Pages 39-48]
Azadi, Mohammad Investigating the effects of geographics climate on the characteristics of statistical data and driving cycle [Volume 70, Issue 2, 2023, Pages 37-65]
Azadi, Mohammad Sensitivity analysis for objectives of power, efficiency, heat loss, and working fluid cost based on input parameters in the Stirling engine [Volume 70, Issue 2, 2023, Pages 1-21]
Azadi, Mohammad Study of the effect of nanoparticles on thermophysical properties and rheological behavior of cooling fluid in combustion engines [Volume 70, Issue 3, 2023, Pages 1-17]
Azadi, Mohammad Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Azargoshasbi, Forood Role of passenger cars and taxies in air pollution of Tehran, Iran [Volume 69, Issue 69, 2022, Pages 21-29]
Azimpour Shishevan, Farzin Investigation of the effect of AL2O3 nanofluid in M13NI engine cooling system [Volume 70, Issue 1, 2023, Pages 47-65]
Azimpour Shishevan, Farzin Experimental analysis of the effect of using aluminum oxide nanofluid in improving the heat transfer of XU7 engine radiator [Volume 70, Issue 2, 2023, Pages 66-79]
Azimpour Shishevan, Farzin Static analysis, fatigue and buckling of connecting rod by finite element method [Volume 71, Issue 3, 2024, Pages 32-44]
Azizi, G. Effect of the tube insert in vehicle radiator on thermal performance [Volume 29, Issue 29, 2013, Pages 39-46]
B
Babaie, M Numerical investigation of the impacts of ammonia injection on the performance of EF7 engine with CNG fuel [Volume 62, Issue 62, 2021, Pages 23-29]
Bagherpoor, Farid Engine Injector Multiphase Flow with Indicated Quantities Simulation for Different Orifice Geometries and Needle Movements [Volume 65, Issue 65, 2022, Pages 21-41]
Baghi Baghban, Hooman Improvement of hardness and tribology properties of engine parts by formation of surface composite layer containing alumina particles by using gas-tungsten arc welding process [Volume 43, Issue 43, 2016, Pages 3-12]
Bahrami, Mohsen Numerical and experimental analysis of lateral vibration of a turbocharger rotor in rotating and non-rotating conditions [Volume 70, Issue 1, 2023, Pages 14-27]
Bahri, B. The effect of ethanol combustion on HCCI engine performance and emissions [Volume 41, Issue 41, 2016, Pages 21-30]
Bahri, Bahram Experimental study of combustion noise level in LTC engine [Volume 51, Issue 51, 2018, Pages 43-52]
Bakhshan, Y. Multi-Dimensional Simulation of n-Heptane Combustion under HCCI Engine Condition Using Detailed Chemical Kinetics [Volume 22, Issue 22, 2011, Pages 3-12]
Bakhshinejad Bahambari, Alireza Numerical study on the effect of geometry on pressure caused by the injectors sealing on the mechanical behavior of common rail fuel of Shahin car at the engine operating temperature conditions [Volume 71, Issue 3, 2024, Pages 1-15]
Baloo, M. Investigation of effect of adding natural gas on gasoline laminar flame speed [Volume 32, Issue 32, 2013, Pages 49-57]
Baloo, M. Laminar flame speed measurement and correlation for methane-iso-octane fuel blend [Volume 39, Issue 39, 2015, Pages 11-20]
Baloo, M. An experimental investigation of the influence of diluent gas on laminar flame speed of natural gas and gasoline fuel mixture [Volume 40, Issue 40, 2015, Pages 47-57]
Baloo, M. Inspection of Impurity effects on the methane laminar flame speed under lean and diluted conditions [Volume 47, Issue 47, 2017, Pages 21-30]
Baloo, M. A study of factors affecting plastics intake manifold strength against backfire phenomena [Volume 48, Issue 48, 2017, Pages 49-57]
Baloo, M. An investigation on the effects of camshaft surface defects on producing high-frequency noises in internal combustion engines [Volume 52, Issue 52, 2018, Pages 3-10]
Banagar, Isa Fuel consumption-aware powertrain selection and optimization for a B-class sedan [Volume 69, Issue 69, 2022, Pages 12-20]
Banakar, A. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Banakar, Ahmad The study on effect of different defects on the timing belt vibrations using data mining and artificial intelligence methods [Volume 36, Issue 36, 2014, Pages 61-70]
Banapurmath, N. Investigation of combustion and emissions of natural gas-diesel dual-fuel PPCI engine [Volume 41, Issue 41, 2016, Pages 13-19]
Banarezaie, Sasan Development of a model based combined Fuzzy-PID controller for idle speed control of internal combustion engine [Volume 38, Issue 38, 2015, Pages 3-16]
Baniamerian, Z. Simulation of Heat Transfer in the Cooling Passages of the âEF7â Engine Considering Boiling Phenomenon [Volume 19, Issue 19, 2010, Pages 64-73]
Baniamerian, Z. Mathematical simulation of a vehicle radiator by genetic algorithm method and comparison with experimental data [Volume 30, Issue 30, 2013, Pages 15-23]
Baratian, Alireza Investigating the effect of bioethanol fuel concentration with different percentages on power and torque in EF7 engine [Volume 70, Issue 3, 2023, Pages 18-29]
Barin, Zahra Defect detection in piston rings using deep learning-based computer vision [Volume 72, Issue 2, 2025, Pages 9-18]
Barzegar, R. Three-Dimensional Modeling of Combustion Process, Soot and NOx formation In a Direct-injection Diesel Engine [Volume 14, Issue 14, 2009, Pages 35-42]
Barzgar, Ramin CFD Simulation of the Biodiesel and Diesel Blends Combustion Process in an In-Direct Injection Diesel Engine [Volume 38, Issue 38, 2015, Pages 39-48]
Bashi, M. Experimental study on effect of cycle-to-cycle variability on HC emission in a SI engine [Volume 33, Issue 33, 2014, Pages 23-30]
Bashiri, Mohamad Investigation of the viscosity of CuO–ZnO hybrid nanolubricant for application in internal combustion engines with a MD approach [Volume 72, Issue 3, 2025, Pages 64-84]
Bashiri, M.R. Recognition of Driving Style, Roadway Type, and Traffic Based on Information Available in Electronic Control unit of Vehicles in Real Traffic Conditions [Volume 17, Issue 17, 2010, Pages 52-59]
Bashi Shahabi, P. Numerical Analysis of Injected EGR/Blowby Gases Distribution in Intake Manifold [Volume 15, Issue 15, 2009, Pages 55-65]
Basir, Hamed Thermal Investigation of turbocharger using infra-red camera [Volume 50, Issue 50, 2018, Pages 3-16]
Basirat Tabrizi, H. Investigation on the Effect of the Cooling Jet Impacts on the Moving Piston on Produced Oil Droplets Using a Motored Engine [Volume 19, Issue 19, 2010, Pages 38-48]
Basirat Tabrizi, H. Experimental investigation on the pumping loss and pressure oscillations in the crankcase [Volume 23, Issue 23, 2011, Pages 3-10]
Basirat Tabrizi, H. Determination of knock borderline ignition timing in turbocharged spark ignition engines [Volume 27, Issue 27, 2012, Pages 33-45]
Basiri, Adel Ratcheting crystal plasticity modeling in microstructure of magnesium alloy under stress-controlled cyclic tensile loading with non-zero mean stress [Volume 68, Issue 68, 2022, Pages 39-48]
Batooei, Alireza Performance and fuel consumption simulation for optimized manual transmission gear ratio selection [Volume 72, Issue 1, 2025, Pages 45-58]
Bayati Nezhad, Mohammad Amir Numerical investigation of the parameters of a prismatic lithium ion battery under load for electrical vehicle [Volume 59, Issue 59, 2020, Pages 45-62]
Bazrafshan, Jafar The Effect of Hydrogen Addition on a RCCI Engine Performance Fueled with Natural GasDiesel Fuel at Low Load Range [Volume 65, Issue 65, 2022, Pages 60-74]
Behzad, M. Valve fault diagnosis in internal combustion engines by acoustic emission method using artificial neural network [Volume 27, Issue 27, 2012, Pages 11-21]
Biglari, Mojtaba Sensitivity analysis for objectives of power, efficiency, heat loss, and working fluid cost based on input parameters in the Stirling engine [Volume 70, Issue 2, 2023, Pages 1-21]
Biglari, Mojtaba Study of the effect of nanoparticles on thermophysical properties and rheological behavior of cooling fluid in combustion engines [Volume 70, Issue 3, 2023, Pages 1-17]
Boroomand, Masoud Simulation and scale-up of a centrifugal compressor for a turbocharger of a lean combustion engine employing 1-D and 3-D design and geometrical modification of the impeller [Volume 66, Issue 66, 2022, Pages 22-35]
Boroushaki, M. Nonlinear Oxygen Sensor Output Voltage Estimation in a Gasoline Engine Using NARX Model [Volume 22, Issue 22, 2011, Pages 13-20]
Bostan Shirin, Hosein Design of Intelligent Cooling System with electrical Thermostat and Implementation of Strategy in Engine Control Unit [Volume 43, Issue 43, 2016, Pages 55-62]
Boutorabi, S.M.A. An Investigation of High Cycle Fatigue Behavior of Magnesium Alloy for Cylinder Head Application [Volume 24, Issue 24, 2011, Pages 29-35]
B. Shokouhi, Shahriar Development of Machine Vision System to Track Movement of an Engine Timing Belt Tensioner Based on Deep Neural Network [Volume 67, Issue 67, 2022, Pages 16-23]
C
Cairns, A. Hydrogen and Oxygen Fuel Enrichment Effects on a HD Diesel Engine [Volume 47, Issue 47, 2017, Pages 13-20]
Caputo, G. Fluid Dynamics Investigation of a GDI Fuel Spray by Particle Image Velocimetry [Volume 14, Issue 14, 2009, Pages 19-26]
Chamani, H. Thermo-Mechanical Fatigue Life Assessment of Diesel Engine Hot Components [Volume 23, Issue 23, 2011, Pages 59-71]
Chamani, H.R. Study of Effects of Combustion Gases and Cooling Thermal Boundary Conditions on Temperature Distribution of a Heavy Duty Diesel Engine Cylinder Head [Volume 17, Issue 17, 2010, Pages 71-81]
Chamehsara, Saeed Effect of fuel injection discharge curve and injection pressure on upgrading power and combustion parameters in HD diesel engine with CFD simulation [Volume 42, Issue 42, 2016, Pages 3-12]
Chapman, K. Experimental Study of Hydrogen Addition Impact on Emissions and Performance of a Natural Gas Fueled Engine [Volume 14, Issue 14, 2009, Pages 43-50]
Checkel, M.D. Reformer Gas Application in Combustion Onset Control of HCCI Engine [Volume 14, Issue 14, 2009, Pages 3-18]
Cheraghmakani, Hooman Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Cheraghmakani, Hooman Experimental investigation of the effect of modifying the engine cooling circuit with the aim of improving the temperature of the cylinder head and block [Volume 71, Issue 3, 2024, Pages 45-55]
Chitsaz, I. Prediction of charge effect on SI engine performance for hydrocarbon fuels [Volume 25, Issue 25, 2012, Pages 25-34]
Chitsaz, I. Effect of hydrogen mole fraction and air-fuel distribution of hydrogen-methane blend on SI engine performance [Volume 27, Issue 27, 2012, Pages 23-31]
Chitsaz, I. A new technique for determination of geometry characteristics, mass flow rate and discharge coefficient of a direct gas injection nozzle [Volume 29, Issue 29, 2013, Pages 57-66]
Chitsaz, I. Investigation of effect of adding natural gas on gasoline laminar flame speed [Volume 32, Issue 32, 2013, Pages 49-57]
Chitsaz, I. Inspection of Impurity effects on the methane laminar flame speed under lean and diluted conditions [Volume 47, Issue 47, 2017, Pages 21-30]
Chitsaz, I. Energy balance on a three-cylinder engine with turbocharger [Volume 49, Issue 49, 2018, Pages 29-38]
Chitsaz, Iman Organic Rankine cycle optimization for waste heat recovery of three-cylinder turbocharged gasoline engine [Volume 64, Issue 64, 2021, Pages 12-27]
Chitsaz, Iman Fuel consumption optimization of a series hybrid electric vehicle utilizing fuzzy logic control [Volume 68, Issue 68, 2022, Pages 23-30]
D
Darvishi, Saba Magnetizing the Perkins A63544 Engine Fuel and Its Vibratory Assessment [Volume 38, Issue 38, 2015, Pages 17-26]
Darvishi, Yousef Modeling and simulation of PEM Used for Automotive Applications [Volume 65, Issue 65, 2022, Pages 75-87]
Dashti, M. Thermodynamic Simulation of Spark Ignition Internal Combustion Engine Operation with Blends of Gasoline and CNG with Experimental Verification [Volume 23, Issue 23, 2011, Pages 32-44]
Dastourani, H. Evaluation of Changes in Soot Formation with Variation of Start Angle of Fuel Injection in Diesel Engine [Volume 24, Issue 24, 2011, Pages 37-49]
Davari, Amirali The process of vehicle engine development at IPCO [Volume 64, Issue 64, 2021, Pages 3-11]
Davari, Sajad Conceptual design of a conventional aero gas turbine combustor for soot and gaseous emissions reduction [Volume 72, Issue 1, 2025, Pages 1-14]
Derikvand, Hadis CFD Simulation of the Biodiesel and Diesel Blends Combustion Process in an In-Direct Injection Diesel Engine [Volume 38, Issue 38, 2015, Pages 39-48]
De Vita, Angelo Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
Dolatyar, Mohammadparsa The effect of using copper nanoparticles in engine oil on fuel consumption [Volume 71, Issue 1, 2024, Pages 52-66]
Domiri Ganji, D. The Effect of Different Injection Configuration on Combustion and Emissions Formation in a Heavy Duty Diesel Engine [Volume 16, Issue 16, 2009, Pages 43-51]
Domiri Ganji, D. 3D simulation of close cycle of spark ignition gas engine and investigation on effects of combustion chamber geometry on power and emissions [Volume 28, Issue 28, 2012, Pages 31-38]
Dowlati, Majid Evaluating the coupled thermo-mechanical stresses for an aluminum alloy piston used in a gasoline engine XU7 [Volume 42, Issue 42, 2016, Pages 33-42]
Duronio, Francesco Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
E
Ebrahimi, Mojtaba The Effect of Hydrogen Addition on a RCCI Engine Performance Fueled with Natural GasDiesel Fuel at Low Load Range [Volume 65, Issue 65, 2022, Pages 60-74]
Ebrahimi, R. Experimental Investigation of Effect of Injection Pressure on Performance of a Diesel Engine Using Blends of Biodiesel and Diesel [Volume 21, Issue 21, 2011, Pages 73-82]
Ebrahimi, R. Study of spark ignition engine emissions fueled by blended hydrogen and methane [Volume 31, Issue 31, 2013, Pages 55-63]
Ebrahimi, R. Study of the performance in dual fuels 50% gasoline -50% NG and single original fuels and comparison in part load [Volume 52, Issue 52, 2018, Pages 11-18]
Ehream, M. A. Experimental study on the efficiency and pressure drop of three different engine types blow by oil separator [Volume 40, Issue 40, 2015, Pages 33-45]
Ehteram, M. A. Simulation of piston and ring friction at the motoring condition and investigation effect of combustion and clearance between the piston and cylinder [Volume 39, Issue 39, 2015, Pages 41-48]
Ehteram, M. A. Effect of oil viscosity on rings and pistons friction using experimental tests and semi-empirical equations in the motoring mode [Volume 48, Issue 48, 2017, Pages 41-48]
Ehteram, M.A Experimental and Analytical Investigation of the Oil Viscosity Effect on Vertical Vibrations of a CI Engine [Volume 46, Issue 46, 2017, Pages 65-74]
Ehteram, M.A. Investigation on the Effect of the Cooling Jet Impacts on the Moving Piston on Produced Oil Droplets Using a Motored Engine [Volume 19, Issue 19, 2010, Pages 38-48]
Ehteram, M.A. Experimental investigation on the pumping loss and pressure oscillations in the crankcase [Volume 23, Issue 23, 2011, Pages 3-10]
Ehteram, M.A. Performance study of a diaphragm type crankcase pressure control valve [Volume 30, Issue 30, 2013, Pages 47-54]
Ehteram, Mohammadali Investigation on the effect of using electric supercharging on the performance of a SI-TC engine [Volume 43, Issue 43, 2016, Pages 41-54]
Emadi, S.A. Performance Enhancement of Hybrid Eclectic Vehicles by Introduction of a Novel Power Split Device [Volume 15, Issue 15, 2009, Pages 36-44]
Emami, Hani Simulation of cylinder deactivation and its effects on emission and fuel consumption [Volume 71, Issue 1, 2024, Pages 79-90]
Erfan, I. A new technique for determination of geometry characteristics, mass flow rate and discharge coefficient of a direct gas injection nozzle [Volume 29, Issue 29, 2013, Pages 57-66]
Esfahanian, V. The effect of ethanol combustion on HCCI engine performance and emissions [Volume 41, Issue 41, 2016, Pages 21-30]
Esfahanian, V. Axial vane rotary engines preliminary design by quasi dimensional modeling technique [Volume 41, Issue 41, 2016, Pages 41-53]
Esfahaniyan, V Improving identification of combustion engine to use in model-based calibration [Volume 63, Issue 63, 2021, Pages 23-34]
Esfandiari, Hamid Optimizing the Shape of Rubber Part of EF7 Engine Mount to Improve its Vibration Behavior [Volume 46, Issue 46, 2017, Pages 49-64]
Esfandiyari, H. Complete and partial vibration mode decoupling of national engine about torque roll axis [Volume 40, Issue 40, 2015, Pages 3-12]
Eskandari, M Investigation of the effect of design variables of a thermoelectric generator on fuel consumption and output power of a vehicle [Volume 63, Issue 63, 2021, Pages 35-47]
Eslami, Maryam The Effect of throttle valve positions on thermomechanical exergy, burned fuel exergy, exergy with heat transfer and exergy with work transfer of an SI Engine [Volume 43, Issue 43, 2016, Pages 31-40]
Esmaeilion, A. Modeling of traffic conditions impact on fuel consumption and emissions of passenger cars in Arak city [Volume 35, Issue 35, 2014, Pages 53-61]
Esmaeili Sany, A.R. Experimental Prediction of Nusselt Number and Coolant Heat Transfer Coefficient in Compact Heat Exchanger Performed with Ñ-NTU Method [Volume 18, Issue 18, 2010, Pages 62-70]
Estahri, M. Analytical and Experimental Modal Analysis of Crankshaft, Flywheel and Pulley Set [Volume 24, Issue 24, 2011, Pages 13-20]
Etelaat, Ali Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Ettefaghi, E. Effects of Nano-Particles on Properties of Engine Oil and its Functionality Rate on Wear Reduction [Volume 24, Issue 24, 2011, Pages 3-12]
F
Faghani, Hamid Design of Intelligent Cooling System with electrical Thermostat and Implementation of Strategy in Engine Control Unit [Volume 43, Issue 43, 2016, Pages 55-62]
Fajri, Hamidreza Accurate Simulation of Low-Pressure Port Fuel and Water Spray in Internal Combustion Engines; Numerical and Experimental Study [Volume 60, Issue 60, 2020, Pages 47-59]
Fajri, H. R. Port Development of a Port Injection Turbocharged Engine to Improve Combustion Quality & Performance Parameters [Volume 49, Issue 49, 2018, Pages 47-66]
Fajri, H. R. Experimental investigation on the effect of injection pressure and injector installation angle on the penetration of the gasoline port fuel injector using high speed imaging method [Volume 52, Issue 52, 2018, Pages 29-42]
Fakhari, Amir Hossein Investigating the influence of injection timing on the performance of a RCCI engine [Volume 70, Issue 1, 2023, Pages 91-105]
Fakhari, V. Vibration control of an automotive engine using active mounts [Volume 30, Issue 30, 2013, Pages 3-14]
Fakhari, V. Dynamic modeling of national engine on mounts together with experimental validation [Volume 33, Issue 33, 2014, Pages 31-41]
Fakhari, V. Complete and partial vibration mode decoupling of national engine about torque roll axis [Volume 40, Issue 40, 2015, Pages 3-12]
Fakhari, Vahid Optimizing the Shape of Rubber Part of EF7 Engine Mount to Improve its Vibration Behavior [Volume 46, Issue 46, 2017, Pages 49-64]
Fakhari, Vahid Dynamic modeling and speed control of a level-one autonomous electric vehicle [Volume 67, Issue 67, 2022, Pages 42-50]
Fakhari, Vahid Mass Properties Identification of a Rigid Body Using Modal Analysis [Volume 68, Issue 68, 2022, Pages 49-55]
Fakravar, Aida Investigation of the Effect of Normal Butanol–Gasoline Blends on the Performance of the Iranian National Engine [(Articles in Press)]
Fallah, H. A study of factors affecting plastics intake manifold strength against backfire phenomena [Volume 48, Issue 48, 2017, Pages 49-57]
Farahat, Said Optimization of fuel consumption and emissions in diesel engines by using of artificial neural network and ant colony algorithm with intake VVT and fuel injection approach [Volume 43, Issue 43, 2016, Pages 13-30]
Farajollahi, Amirhamzeh Engine Injector Multiphase Flow with Indicated Quantities Simulation for Different Orifice Geometries and Needle Movements [Volume 65, Issue 65, 2022, Pages 21-41]
Farhang, B. Experimental study of a spark ignition single-cylinder research engine exhaust emissions in gasoline and natural gas fuel cases [Volume 39, Issue 39, 2015, Pages 49-55]
Farhang, K. Experimental Investigation of the Combustion of a Spark Ignition Engine, With Gasoline-Ethanol-MTBE Blends as Fuel, to Reduce Fuel Consumption and pollutants [Volume 16, Issue 16, 2009, Pages 22-28]
Faridi, Hamideh Evaluate the effect of biodiesel and EGR system on diesel engine emissions [Volume 42, Issue 42, 2016, Pages 23-32]
Farokhinejad, Mehrdad Parametric performance of tandem oscillating airfoils and an exploration of dragonfly wing potential in enhancing propulsive efficiency [Volume 72, Issue 1, 2025, Pages 59-88]
Farrahi, G.H. Failure Analysis of a Four Cylinder Diesel Engine Crankshaft Made From Nodular Cast Iron [Volume 22, Issue 22, 2011, Pages 21-28]
Farrahi, G.H. Coating thickness effect on stress distribution of coated cylinder head considering residual stress [Volume 26, Issue 26, 2012, Pages 49-57]
Farrahi, G.H. Low cycle fatigue analysis of magnesium alloy cylinder head based on plastic strain energy approach [Volume 27, Issue 27, 2012, Pages 3-10]
Farrahi, G.H. Finite element analysis of thermal and mechanical stresses in diesel engine cylinder head using two-layer elastic-viscoplastic model [Volume 28, Issue 28, 2012, Pages 51-60]
Farshchi, Mohammad Acoustic extintion of partially premixed counterflow flame [Volume 70, Issue 3, 2023, Pages 39-52]
Farshi Fasih, Hamidreza Gasification of petroleum and chemical base fuels with the aim of hydrogen-rich syngas [Volume 70, Issue 3, 2023, Pages 30-38]
Farshi Fasih, Hamidreza Aerothermodynamic off-design performance study of a fixed double bypass duct turbofan engine [Volume 70, Issue 3, 2023, Pages 62-75]
Fathi, M. Fuel reactivity as a means to control DI-HCCI combustion engine [Volume 47, Issue 47, 2017, Pages 39-46]
Fazel, Mahmoud Surface composite create layer metal / ceramic by coating gas tungsten arc to improve the hardness and wear resistance of engine parts [Volume 36, Issue 36, 2014, Pages 39-50]
Fazel Najafabadi, M. Creation of ceramic-metal joint in new generation of high heat resistant engines by brazing [Volume 27, Issue 27, 2012, Pages 59-65]
Fekri, Yashar Temperature simulation of a prismatic 8 Ah lithium-iron-phosphate battery using the Bernardi equation [Volume 72, Issue 1, 2025, Pages 15-24]
Feyz, M.E. Experimental Investigation on the Effect of EGR Mixture Temperature on the Second Law Efficiency in Light-duty Diesel Engines [Volume 20, Issue 20, 2010, Pages 12-21]
Firouzgan, A. An Experimental Assessment of Compression Ratio and Evaluation of Aluminium Cylinder Head in Bi-Fuel(Gasoline+CNG) Engines [Volume 18, Issue 18, 2010, Pages 51-61]
Firuzi, Reza Engine Injector Multiphase Flow with Indicated Quantities Simulation for Different Orifice Geometries and Needle Movements [Volume 65, Issue 65, 2022, Pages 21-41]
Fontaras, G. Reducing CO2 Emissions from Road Transport - Overview of the Main Initiatives and Technical Measures Proposed to Date in Europe [Volume 18, Issue 18, 2010, Pages 32-41]
Forozandehnasab, Mojtaba Investigation of a preventive service model of service and maintenance for common rail diesel engines [Volume 66, Issue 66, 2022, Pages 46-56]
Forozandehnasab, Mojtaba Evaluation of changes in diesel fuel type on the injection rate of diesel common rail injectors [Volume 72, Issue 3, 2025, Pages 43-63]
Fotouhi, A. Driving Features and Their Influences on Hybrid Electric Vehicleâs Fuel Consumption and Exhaust Emissions [Volume 17, Issue 17, 2010, Pages 42-51]
Froutan, O. A study of factors affecting plastics intake manifold strength against backfire phenomena [Volume 48, Issue 48, 2017, Pages 49-57]
Froutan, O. Investigating the effect of nanocoating on friction loss and abrasion in the piston rings [Volume 53, Issue 53, 2019, Pages 13-22]
G
Garivani, Mahdi Development of an in-cylinder processes model of a CVVT gasoline engine using artificial neural network [Volume 51, Issue 51, 2018, Pages 53-62]
Gerdooei, Mahdi Investigation of parameters influencing production rate and power consumption in Cut-Wire process for shot peening of automotive springs [Volume 72, Issue 2, 2025, Pages 31-42]
Ghadamian, Hossein Investigation of Three-Way Catalytic Converters of a 1.7L Turbocharged Bi-Fuel Engine Using CNG and Gasoline Fuels [Volume 44, Issue 44, 2016, Pages 53-64]
Ghadimi, Behnam Investigation of the Effect of the Geometric Deviations on the Performance of a Radial Flow Compressor Employing Uncertainty Quantification (UQ) and Sensitivity Analysis [Volume 67, Issue 67, 2022, Pages 51-63]
Ghadimi, N. 3D simulation of close cycle of spark ignition gas engine and investigation on effects of combustion chamber geometry on power and emissions [Volume 28, Issue 28, 2012, Pages 31-38]
Ghadimi, P. Numerical study of effect of ambient backpressure and temperature on spray characteristics of heavy fuel oil/n-butanol blend [Volume 31, Issue 31, 2013, Pages 43-53]
Ghadimi, P. Numerical investigation of non-reacting spray characteristics of heavy âfuel and alternative fuel under high injection pressure [Volume 34, Issue 34, 2014, Pages 3-15]
Ghadimi, Parviz A Numerical Study on Non-Reacting Spray Characteristics of Different Marine Diesel Fuel-Water Emulsion Blends [Volume 44, Issue 44, 2016, Pages 65-77]
Ghaedi, Ashkan Experimental investigation of injection timing effect on RCCI Engine using waste oil biodiesel as high reactive fuel [Volume 71, Issue 4, 2025, Pages 44-57]
Ghaedi Kachooee, Mohammad Numerical investigation on improvement of cooling system based on heat pipe for LCO battery by using NTGK model [Volume 71, Issue 2, 2024, Pages 69-90]
Ghafouri, Jafar Study on the effect of using reformed biogas as a low reactivity fuel in a dual-fuel engine (RCCI) [Volume 59, Issue 59, 2020, Pages 73-93]
Ghafuri, M. Effect Investigation of Important Parameters in Knock Detection Using Cylinder Pressure Data [Volume 17, Issue 17, 2010, Pages 3-14]
Ghanbari, Mani Experimental study on the effect of Al2O3 nanoparticles in diesel fuel on the performance and emission characteristics of a diesel engine [Volume 61, Issue 61, 2021, Pages 35-45]
Gharaati, M. A study of contact heat transfer problem in exhaust valve of internal âcombustion engines [Volume 34, Issue 34, 2014, Pages 51-60]
Ghareghani, A. Heat Balance of a Natural Gas Fueled Spark Ignition Engine with a Turbocharger [Volume 20, Issue 20, 2010, Pages 45-58]
Gharehghani, Ayat Investigating the influence of injection timing on the performance of a RCCI engine [Volume 70, Issue 1, 2023, Pages 91-105]
Gharehghani, Ayat Developing a reduced chemical kinetic mechanism for natural gas/biodiesel mixture combustion [Volume 71, Issue 4, 2025, Pages 15-32]
Gharehghani, Ayat Impact of pressure on thermal efficiency of phase change material-based BTMS for electric powertrain [Volume 71, Issue 3, 2024, Pages 16-31]
Gharloghy, J. Thermal Analysis of an SI Engine Piston Using Different Thermal Model [Volume 17, Issue 17, 2010, Pages 28-41]
Ghasemi, A. A New Approach for Inlet Diffuser of Automotive Catalytic Converter Considering Conversion Efficiency of Pollutants [Volume 18, Issue 18, 2010, Pages 42-50]
Ghasemi, J. Simulating and prototyping of a compression ring for diesel engine regarding required spring back force [Volume 32, Issue 32, 2013, Pages 21-28]
Ghasemi, M. Analysis of Contact Stresses and MLS Cylinder Head Gasket Behavior Using Finite Element Method [Volume 15, Issue 15, 2009, Pages 45-54]
Ghasemian Moghadam, A. Reducing of Transient Warm-up Period in an Internal Combustion Engine by Preheating of Engine Parts [Volume 17, Issue 17, 2010, Pages 15-27]
Ghasemi-Ghalebahman, Ahmad Ratcheting crystal plasticity modeling in microstructure of magnesium alloy under stress-controlled cyclic tensile loading with non-zero mean stress [Volume 68, Issue 68, 2022, Pages 39-48]
Ghassemi, M.R. Vibration Control by a Semi-Active Air Spring System in High Frequency by PID Controller in Engine Test Cell [Volume 20, Issue 20, 2010, Pages 30-44]
Ghayour, Mostafa Numerical and experimental analysis of lateral vibration of a turbocharger rotor in rotating and non-rotating conditions [Volume 70, Issue 1, 2023, Pages 14-27]
Ghazanfar, H. Study on effect of electric/combustion engine on performance of a parallel hybrid vehicle and proposing engine selection algorithm [Volume 31, Issue 31, 2013, Pages 21-31]
Ghazikhani, M. Experimental Investigation on the Effect of EGR Mixture Temperature on the Second Law Efficiency in Light-duty Diesel Engines [Volume 20, Issue 20, 2010, Pages 12-21]
Ghazikhani, M. Experimental Investigation of the EGR Temperature Effects on the Destruction of the Fuelâs Availability Due to Combustion Processes in IDI Diesel Engine Cylinder [Volume 22, Issue 22, 2011, Pages 62-68]
Ghazikhani, M. Evaluation of Changes in Soot Formation with Variation of Start Angle of Fuel Injection in Diesel Engine [Volume 24, Issue 24, 2011, Pages 37-49]
Ghobadian, B. Experimental Investigation of Effect of Injection Pressure on Performance of a Diesel Engine Using Blends of Biodiesel and Diesel [Volume 21, Issue 21, 2011, Pages 73-82]
Ghobadian, B. Simulation of vibration for a diesel engine with biodiesel and diesel fuel blends using artificial neural networks [Volume 23, Issue 23, 2011, Pages 22-31]
Ghobadian, B. Modeling of an SI engine performance parameters and emissions using bio-ethanol-gasoline blends by genetic programming [Volume 27, Issue 27, 2012, Pages 47-57]
Ghobadian, B. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Ghobadian, B. Optimization of performance in tractor engine with biodiesel-ethanol-diesel fuels using response surface methodology [Volume 29, Issue 29, 2013, Pages 15-24]
Ghobadian, B. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Ghobadian, B. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Ghobadian, B. Investigation of diesel fuel and soybean methyl esters emission in high-speed diesel engine [Volume 35, Issue 35, 2014, Pages 31-39]
Ghobadian, Barat Piston scuffing fault identification using engine vibration analysis [Volume 36, Issue 36, 2014, Pages 3-14]
Ghobadian, Barat The study on effect of different defects on the timing belt vibrations using data mining and artificial intelligence methods [Volume 36, Issue 36, 2014, Pages 61-70]
Ghobadian, Barat Magnetizing the Perkins A63544 Engine Fuel and Its Vibratory Assessment [Volume 38, Issue 38, 2015, Pages 17-26]
Ghobadian, Barat Functional Variables of a Biodiesel-Powered Single-Cylinder Diesel Engine: an Experimental Analysis [Volume 38, Issue 38, 2015, Pages 49-60]
Ghobadian, Barat The Effect of throttle valve positions on thermomechanical exergy, burned fuel exergy, exergy with heat transfer and exergy with work transfer of an SI Engine [Volume 43, Issue 43, 2016, Pages 31-40]
Ghobadian, Barat Evaluation of Performance and Vibration of a Diesel Engine Using Ag Nanoparticles Added to Diesel and Biodiesel Fuel Blends [Volume 46, Issue 46, 2017, Pages 15-26]
Ghobadian, Barat Comparison of Aged and fresh Automotive Three-Way Catalyst in Driving Cycle [Volume 57, Issue 57, 2020, Pages 75-83]
Ghobadian, Barat Vibration analysis of turbocharger in different clogging conditions of Diesel Particle Filter (DPF) [Volume 70, Issue 1, 2023, Pages 66-90]
Ghobadian, Barat Agricultural tractor driving cycle extraction using artificial intelligence [Volume 70, Issue 4, 2024, Pages 14-26]
Ghodrati, M. Finite element analysis of thermal and mechanical stresses in diesel engine cylinder head using two-layer elastic-viscoplastic model [Volume 28, Issue 28, 2012, Pages 51-60]
Ghodsi, A Numerical investigation of the impacts of ammonia injection on the performance of EF7 engine with CNG fuel [Volume 62, Issue 62, 2021, Pages 23-29]
Gholami, Yasamin Dynamic modeling and speed control of a level-one autonomous electric vehicle [Volume 67, Issue 67, 2022, Pages 42-50]
Ghorbanian, J. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Ghorbanian, J. A New Approach to Flow Network Analysis of an Engine Lubrication System [Volume 18, Issue 18, 2010, Pages 12-19]
Ghoreishi, Majid Experimental investigation of the effect of changing elements in the cylinder liner of BMP1 diesel engine on surface hardness [Volume 72, Issue 1, 2025, Pages 25-34]
Golbakhshi, Hossein Evaluating the coupled thermo-mechanical stresses for an aluminum alloy piston used in a gasoline engine XU7 [Volume 42, Issue 42, 2016, Pages 33-42]
Golbakhshi, Hossein Numerical investigation on Effect of thermally isolated piston on improving SI engine performance during the cold start conditions [Volume 47, Issue 47, 2017, Pages 3-12]
Golbodaghi, Masoud Predicting the remaining useful life of diesel engine oil using Gaussian process regression [Volume 71, Issue 3, 2024, Pages 77-91]
Gorji, M. 3D simulation of close cycle of spark ignition gas engine and investigation on effects of combustion chamber geometry on power and emissions [Volume 28, Issue 28, 2012, Pages 31-38]
Gorji-Bandpy, Mofid Experimental study of the diesel injector nozzle sediment effect on fuel spray behavior [Volume 54, Issue 54, 2019, Pages 13-23]
Goudarzi, K. Effect of the tube insert in vehicle radiator on thermal performance [Volume 29, Issue 29, 2013, Pages 39-46]
Goudarzi, K. A study of contact heat transfer problem in exhaust valve of internal âcombustion engines [Volume 34, Issue 34, 2014, Pages 51-60]
H
Haddadi, Farhad Investigation of torque and power output of power generation system in hybrid electric vehicles with parallel arrangement in driving modes [Volume 64, Issue 64, 2021, Pages 54-66]
Haeri Yazdi, M Improving identification of combustion engine to use in model-based calibration [Volume 63, Issue 63, 2021, Pages 23-34]
Hajalimohammadi, Alireza Defect detection in piston rings using deep learning-based computer vision [Volume 72, Issue 2, 2025, Pages 9-18]
Haji Agha Alizade, Hossein Investigation of performance and exhaust emission of diesel engine in different ratios of lambda coefficient using diesel-ethanol fuel blends [Volume 60, Issue 60, 2020, Pages 19-28]
Haji agha alizadeh, Hossien Evaluate the effect of biodiesel and EGR system on diesel engine emissions [Volume 42, Issue 42, 2016, Pages 23-32]
Hajialiakbari, F. Formation of diesel-water nano-emulsion: Importance, advantages and evaluation of engine performance [Volume 33, Issue 33, 2014, Pages 53-60]
Haji Alimohamadi, Alireza Investigating of Process Design Parameters in 4043 alloy Additive Manufactured specimens, to create external features of cylinder head [Volume 60, Issue 60, 2020, Pages 3-17]
Hajialimohammadi, A. A new technique for determination of geometry characteristics, mass flow rate and discharge coefficient of a direct gas injection nozzle [Volume 29, Issue 29, 2013, Pages 57-66]
Hajialimohammadi, A. Sensitivity analysis of parameters affecting image processing of high pressure gaseous jet images [Volume 33, Issue 33, 2014, Pages 43-52]
Hajialimohammadi, A. A novel experimental test rig for simulating of the fuel injection system components behavior under cold conditions [Volume 47, Issue 47, 2017, Pages 31-38]
Hajialimohammadi, Alireza Experimental study of the diesel injector nozzle sediment effect on fuel spray behavior [Volume 54, Issue 54, 2019, Pages 13-23]
Hajialimohammadi, Alireza Numerical and experimental investigation of common rail fuel injection system and evaluating influence of fuel pressure on injection characteristics and pressure fluctuations [Volume 59, Issue 59, 2020, Pages 63-72]
Hajialimohammadi, Alireza Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
Hajialimohammadi, Alireza Numerical investigation the effect of accumulator on reducing the pressure waves in a common rail fuel injection system of diesel engine [Volume 68, Issue 68, 2022, Pages 31-38]
Hajialimohammadi, Alireza Investigating the effect of the coating process on improving the quality of mechanical bonding in the casting of aluminum cylinder block with cast-in iron liner [Volume 70, Issue 2, 2023, Pages 80-98]
Hajialimohammadi, Alireza Development of an electrochemical deburring process using ultrasonic waves for combustion engine oil spring ring [Volume 71, Issue 2, 2024, Pages 55-68]
Hajiali Mohammadi, A. Experimental investigation of the effect of pressure and density ratio on the gaseous spray of the group-hole nozzle [Volume 28, Issue 28, 2012, Pages 11-19]
Hajiali Mohammadi, A. EF7 engine flywheel bolted joint design improvement by theoretical and experimental investigations [Volume 48, Issue 48, 2017, Pages 27-40]
Hajiali Mohammadi, A. Experimental investigation on the effect of injection pressure and injector installation angle on the penetration of the gasoline port fuel injector using high speed imaging method [Volume 52, Issue 52, 2018, Pages 29-42]
Hajiali Mohammadi, Alireza Optimization of solution temperature and time in nickel-based super-alloy of engine turbo-charger based on hardness by design of experiments [Volume 43, Issue 43, 2016, Pages 63-70]
Hajiali Mohammadi, Alireza Investigating the effect of bioethanol fuel concentration with different percentages on power and torque in EF7 engine [Volume 70, Issue 3, 2023, Pages 18-29]
Haji_Ali_Mohammadi, Alireza Concept selection for engine components using the DEMATEL-ANP-TOPSIS combination method: case study for cam bearing frame part [Volume 61, Issue 61, 2021, Pages 61-71]
Hamad, A. H. Effect of tumble flap on combustion and performance of NA national engine [Volume 49, Issue 49, 2018, Pages 3-18]
Hamidi, A. Investigation of diesel fuel and soybean methyl esters emission in high-speed diesel engine [Volume 35, Issue 35, 2014, Pages 31-39]
Hamidi, A.A. Thermodynamic Simulation of Spark Ignition Internal Combustion Engine Operation with Blends of Gasoline and CNG with Experimental Verification [Volume 23, Issue 23, 2011, Pages 32-44]
Hamidi, Asghar Investigation of Three-Way Catalytic Converters of a 1.7L Turbocharged Bi-Fuel Engine Using CNG and Gasoline Fuels [Volume 44, Issue 44, 2016, Pages 53-64]
Hasandokht, Abdollah Experimental study of porous medium effect on pollutant emissions and fuel consumption for motorcycles [Volume 45, Issue 45, 2017, Pages 53-62]
Hasani, A. Investigating the effect of using catalytic converters and changing fuel supply system on motorcycle emission performance [Volume 40, Issue 40, 2015, Pages 13-22]
Hashemi, Masud Optimization of Cam-Follower Curve of Rotary Vane Engine on Dynamic Analysis [Volume 64, Issue 64, 2021, Pages 67-80]
Hashemi, Seyed Masoud Optimization of car gearbox conversion ratios based on providing maximum traction in different gears [Volume 66, Issue 66, 2022, Pages 36-45]
Hashemi, S.J. The initial estimate of the useful life of the oil in diesel engines using oil analysis [Volume 25, Issue 25, 2012, Pages 45-55]
Hashemi Daryan, J. Study of spark ignition engine emissions fueled by blended hydrogen and methane [Volume 31, Issue 31, 2013, Pages 55-63]
Hashemi Daryan, Jafar Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Hashemi Daryan, Jafar Acoustic signal-based misfire detection in internal combustion engines using machine learning techniques [(Articles in Press)]
Hassan-beygi, Seyed Reza Numerical and experimental investigation of common rail fuel injection system and evaluating influence of fuel pressure on injection characteristics and pressure fluctuations [Volume 59, Issue 59, 2020, Pages 63-72]
Hassan-Beygi, Reza Modeling and simulation of PEM Used for Automotive Applications [Volume 65, Issue 65, 2022, Pages 75-87]
Hassan-Beygi, Seyed Reza Numerical investigation the effect of accumulator on reducing the pressure waves in a common rail fuel injection system of diesel engine [Volume 68, Issue 68, 2022, Pages 31-38]
Hassani Gangaraj, S.M. Failure Analysis of a Four Cylinder Diesel Engine Crankshaft Made From Nodular Cast Iron [Volume 22, Issue 22, 2011, Pages 21-28]
Hassanzadeh, Ezatollah Experimental investigation on the gamma model Stirling engine for cooling production using various gases [Volume 59, Issue 59, 2020, Pages 17-28]
Heidari, Mehdi An investigation on the effect of interference clearance of bushing on fatigue strength in triangle suspension [Volume 67, Issue 67, 2022, Pages 30-41]
Hematian, Rasoul Numerical investigation the effect of accumulator on reducing the pressure waves in a common rail fuel injection system of diesel engine [Volume 68, Issue 68, 2022, Pages 31-38]
HEMATIAN, RASOUL Numerical and experimental investigation of common rail fuel injection system and evaluating influence of fuel pressure on injection characteristics and pressure fluctuations [Volume 59, Issue 59, 2020, Pages 63-72]
Hemmati, F. Failure Analysis of a Four Cylinder Diesel Engine Crankshaft Made From Nodular Cast Iron [Volume 22, Issue 22, 2011, Pages 21-28]
Hemmati, Mansour The effect of using copper nanoparticles in engine oil on fuel consumption [Volume 71, Issue 1, 2024, Pages 52-66]
Hemmatian, R. Effect of tumble flap on combustion and performance of NA national engine [Volume 49, Issue 49, 2018, Pages 3-18]
Hemmatkhanloo, R. Research on modification of cooling passage for a 4-cylinder turbo-charged SI engine with precise cooling view point [Volume 41, Issue 41, 2016, Pages 31-39]
Hemmat Khanlou, R. Simulation of heat transfer considering boiling phenomenon in cooling passage of turbo-charged national engine [Volume 29, Issue 29, 2013, Pages 3-14]
Heshmati, Navid Experimental study and 3D numerical simulation of the effect of pressure ratio on flow divergence efficiency of a linear aerospike nozzle [Volume 70, Issue 3, 2023, Pages 53-61]
Heyhat, Mohammad Mahdi Temperature simulation of a prismatic 8 Ah lithium-iron-phosphate battery using the Bernardi equation [Volume 72, Issue 1, 2025, Pages 15-24]
Hojjat, Y. Vibration Control by a Semi-Active Air Spring System in High Frequency by PID Controller in Engine Test Cell [Volume 20, Issue 20, 2010, Pages 30-44]
Holzberger, Sascha Experimental investigations on a pre-chamber spark plug with variable heat range by integrating a controlled hot surface [Volume 69, Issue 69, 2022, Pages 3-11]
Homaeinezhad, Mohammad Reza Designing Nonlinear Digital Controller for Switching Non Affine Process of Spark Ignition Engine Catalyst Warm-Up [Volume 65, Issue 65, 2022, Pages 42-59]
Honnery, D. Experimental investigation of the effect of pressure and density ratio on the gaseous spray of the group-hole nozzle [Volume 28, Issue 28, 2012, Pages 11-19]
Honnery, D. Sensitivity analysis of parameters affecting image processing of high pressure gaseous jet images [Volume 33, Issue 33, 2014, Pages 43-52]
Hooresfand, R. Experimental investigation of injector pump type effect on performance âparameters and emissions of âdiesel engine at full load [Volume 34, Issue 34, 2014, Pages 61-70]
Hooshang, M. Dynamic-Thermodynamic Mathematical Model of Stirling Engine to Improve Efficiency and Power [Volume 23, Issue 23, 2011, Pages 72-85]
Hooshyari, Khadijeh Modeling and simulation of PEM Used for Automotive Applications [Volume 65, Issue 65, 2022, Pages 75-87]
Hoseini, S. V. Optimization of Online induction Sensor for Ferrous Metals Particles Identification in Engine Oil [Volume 53, Issue 53, 2019, Pages 3-12]
Hoseini, V. Experimental investigation of gasoline fueled HCCI engine load expansion [Volume 39, Issue 39, 2015, Pages 3-10]
Hoseinpoor, Marziye Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Hossainpur, S. Optimizing exhaust noise and back pressure of exhaust system in turbo-charged three-liter diesel engine [Volume 35, Issue 35, 2014, Pages 63-70]
Hosseini, Ali Reza Development of Machine Vision System to Track Movement of an Engine Timing Belt Tensioner Based on Deep Neural Network [Volume 67, Issue 67, 2022, Pages 16-23]
Hosseini, M. A framework for prioritizing improvement and development of engine [Volume 28, Issue 28, 2012, Pages 39-49]
Hosseini, M.A. Simulating and prototyping of a compression ring for diesel engine regarding required spring back force [Volume 32, Issue 32, 2013, Pages 21-28]
Hosseini, Mahdi Verification of the performance of the paddle wheel swirl meter using numerical simulation and experimental test [Volume 70, Issue 4, 2024, Pages 40-55]
Hosseini, Seyed Ehsan Conceptual design of a conventional aero gas turbine combustor for soot and gaseous emissions reduction [Volume 72, Issue 1, 2025, Pages 1-14]
Hosseini, Seyed Vahid Investigation the effect of clamping stress on ultrasonic velocity in cylinder head bolt of diesel engine [Volume 50, Issue 50, 2018, Pages 29-40]
Hosseini, Seyed Vahid An investigation on the effect of interference clearance of bushing on fatigue strength in triangle suspension [Volume 67, Issue 67, 2022, Pages 30-41]
Hosseini, S. V Numerical investigation of the impacts of ammonia injection on the performance of EF7 engine with CNG fuel [Volume 62, Issue 62, 2021, Pages 23-29]
Hosseini, S. V Modeling of Motor Oil Containing Diamond Nanoparticle Between two Iron Abrasion Surfaces Using Molecular Dynamics Methods [Volume 62, Issue 62, 2021, Pages 31-41]
Hosseini, S. V. Effective of Main Bearing Bolt Manufacturing Parameters on Functional Performance in High Speed Diesel Engine using Torque-Angle Method [Volume 52, Issue 52, 2018, Pages 55-63]
Hosseini, S. V. Oil Quality Monitoring in Gasoline Spark Ignition Engine Using Oil Dielectric Measurement [Volume 53, Issue 53, 2019, Pages 45-54]
Hosseini, S.V. Reformer Gas Application in Combustion Onset Control of HCCI Engine [Volume 14, Issue 14, 2009, Pages 3-18]
Hosseini, S.V. Investigation on the Effect of the Cooling Jet Impacts on the Moving Piston on Produced Oil Droplets Using a Motored Engine [Volume 19, Issue 19, 2010, Pages 38-48]
Hosseini, S.V. Investigation of Effects of Spark Plugâs Electrodes Erosion on the Required Ignition Voltage and Performance of Natural Gas Engine [Volume 21, Issue 21, 2011, Pages 21-34]
Hosseini, S.V. Effect of electrode erosion on the required ignition voltage of spark plug in CNG spark ignition engine [Volume 26, Issue 26, 2012, Pages 31-39]
Hosseini, V. Experimental investigation and statistical analysis of cyclic variations in homogeneous charge compression ignition combustion engine [Volume 31, Issue 31, 2013, Pages 3-10]
Hosseini, V. Controlling natural gas combustion timing in HCCI engine with synthetic gas enrichment using a chemical kinetic model [Volume 32, Issue 32, 2013, Pages 13-20]
Hosseini, V. Investigating the effect of using catalytic converters and changing fuel supply system on motorcycle emission performance [Volume 40, Issue 40, 2015, Pages 13-22]
Hosseini, V. Effect of Crossing Diesel Fleet in Tehran on Black Carbon Air Pollution [Volume 49, Issue 49, 2018, Pages 19-28]
Hosseini, Vahid Development of a 3D CFD model to analyze gas exchange process into intake manifold of an iVVT engine [Volume 36, Issue 36, 2014, Pages 51-60]
Hosseini Ansaroudi, Amir Development of a zero-dimensional turbulence model for the flow field of spark-ignition engines, considering vortex motions, based on a new approach [Volume 71, Issue 4, 2025, Pages 77-101]
Hosseinipour, Zahra Experimental study and 3D numerical simulation of the effect of pressure ratio on flow divergence efficiency of a linear aerospike nozzle [Volume 70, Issue 3, 2023, Pages 53-61]
Hosseinkhani, Mohammad Javad Acoustic extintion of partially premixed counterflow flame [Volume 70, Issue 3, 2023, Pages 39-52]
Hossein Nezhad, Alireza Optimization of fuel consumption and emissions in diesel engines by using of artificial neural network and ant colony algorithm with intake VVT and fuel injection approach [Volume 43, Issue 43, 2016, Pages 13-30]
Hosseinpour Sharafshad, Mohammad Experimental investigation of the effect of changing elements in the cylinder liner of BMP1 diesel engine on surface hardness [Volume 72, Issue 1, 2025, Pages 25-34]
Hosseinzadeh Samani, Bahram Artificial neural network model to predict the performance of a diesel power generator fueled with biodiesel [Volume 42, Issue 42, 2016, Pages 43-50]
Hosseinzadeh Samani, Bahram Emission Characteristics of a Diesel Engine fueled with Diesel-biodiesel-JP-4 Blends [Volume 57, Issue 57, 2020, Pages 3-14]
Houshyar, Moslem Optimization of car gearbox conversion ratios based on providing maximum traction in different gears [Volume 66, Issue 66, 2022, Pages 36-45]
I
Iranmanesh, M. Effect of combustion products of gasoline-ethanol blended fuel on corrosion of valve and cylinder head alloys of SI engines [Volume 28, Issue 28, 2012, Pages 3-10]
Iziy, Mostafa Optimization of solution temperature and time in nickel-based super-alloy of engine turbo-charger based on hardness by design of experiments [Volume 43, Issue 43, 2016, Pages 63-70]
J
Jabbarzadeh, M. Numerical comparison of physical conditions effect on spray behavior of dimethyl ether, biodiesel and diesel fuels [Volume 35, Issue 35, 2014, Pages 17-29]
Jabbarzadeh, P. Numerical comparison of physical conditions effect on spray behavior of dimethyl ether, biodiesel and diesel fuels [Volume 35, Issue 35, 2014, Pages 17-29]
Jadali, Ali Investigating the effect of the coating process on improving the quality of mechanical bonding in the casting of aluminum cylinder block with cast-in iron liner [Volume 70, Issue 2, 2023, Pages 80-98]
Jadidi, Amir Mohammad Investigating the effect of bioethanol fuel concentration with different percentages on power and torque in EF7 engine [Volume 70, Issue 3, 2023, Pages 18-29]
Jafari, B. The Effect of Different Injection Configuration on Combustion and Emissions Formation in a Heavy Duty Diesel Engine [Volume 16, Issue 16, 2009, Pages 43-51]
Jafari, M. J. An investigation on the effects of camshaft surface defects on producing high-frequency noises in internal combustion engines [Volume 52, Issue 52, 2018, Pages 3-10]
Jafari, Mohamad The process of vehicle engine development at IPCO [Volume 64, Issue 64, 2021, Pages 3-11]
Jafari, Seyed Mohammad Dynamic analysis of three-cylinder engine with balancing shaft [Volume 60, Issue 60, 2020, Pages 61-75]
Jafari, Seyed Mohammad Predicting the remaining useful life of diesel engine oil using Gaussian process regression [Volume 71, Issue 3, 2024, Pages 77-91]
Jafari, Seyyed Mohammad Thermal Investigation of turbocharger using infra-red camera [Volume 50, Issue 50, 2018, Pages 3-16]
Jafari, S. M. Study of ball bearings failure modes in an eddy current dynamometer [Volume 41, Issue 41, 2016, Pages 3-11]
Jafari, S.M. Health monitoring and performance investigation of accessory belt in an internal combustion engine during critical speeds [Volume 25, Issue 25, 2012, Pages 3-12]
Jafari, S.M. Valve fault diagnosis in internal combustion engines by acoustic emission method using artificial neural network [Volume 27, Issue 27, 2012, Pages 11-21]
Jafari, S.M. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Jafari, S.M. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Jafari, S.M. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Jafari Mehrabadi, Saeed Experimental investigation on the gamma model Stirling engine for cooling production using various gases [Volume 59, Issue 59, 2020, Pages 17-28]
Jafarmadar, S. Three-Dimensional Modeling of Combustion Process, Soot and NOx formation In a Direct-injection Diesel Engine [Volume 14, Issue 14, 2009, Pages 35-42]
Jafarmadar, S. Investigation of combustion and emissions of natural gas-diesel dual-fuel PPCI engine [Volume 41, Issue 41, 2016, Pages 13-19]
Jafarmadar, Samad Experimental investigation and simulation of lean burn combustion in a SI natural gas engine using prechambered spark plug [Volume 50, Issue 50, 2018, Pages 41-54]
Jahandideh, Farbod Experimental study of combustion noise level in LTC engine [Volume 51, Issue 51, 2018, Pages 43-52]
Jahanian, O. A Comprehensive Study on the Leading Factors Affecting on the Start of Combustion in a Homogenous Charge Compression Ignition (HCCI) Engine Fueled with Methane [Volume 20, Issue 20, 2010, Pages 69-79]
Jahanian, O. Using a single zone thermodynamic model in an HCCI engine to predict effective controlling parameters [Volume 25, Issue 25, 2012, Pages 13-23]
Jahanian, O. Study of spark ignition engine emissions fueled by blended hydrogen and methane [Volume 31, Issue 31, 2013, Pages 55-63]
Jahanian, O. Developing a multi-zone thermo-kinetic model to investigate effects of using DME-methane blend in an HCCI engine [Volume 32, Issue 32, 2013, Pages 37-47]
Jahanian, O. Fuel reactivity as a means to control DI-HCCI combustion engine [Volume 47, Issue 47, 2017, Pages 39-46]
Jahanian, Omid Investigation on the Effects of Geometrical Specifications of Injection on Performance of a Direct Injection Hydrogen Fueled Engine [Volume 37, Issue 37, 2015, Pages 13-24]
Jahanian, Omid Evaluation of the Effects of Equivalence Ratio on the Combustion in an HCCI Engine [Volume 61, Issue 61, 2021, Pages 47-59]
Jahanian, Omid Feasibility Study for Downsizing EF7 Engine, Numerical and Experimental Approach [Volume 61, Issue 61, 2021, Pages 73-85]
Jahanian, Omid Experimental investigation of injection timing effect on RCCI Engine using waste oil biodiesel as high reactive fuel [Volume 71, Issue 4, 2025, Pages 44-57]
Jalali, Hossein Investigation of parameters influencing production rate and power consumption in Cut-Wire process for shot peening of automotive springs [Volume 72, Issue 2, 2025, Pages 31-42]
Jalali, Mohammad Hadi Numerical and experimental analysis of lateral vibration of a turbocharger rotor in rotating and non-rotating conditions [Volume 70, Issue 1, 2023, Pages 14-27]
Jamali, M. Determination of knock borderline ignition timing in turbocharged spark ignition engines [Volume 27, Issue 27, 2012, Pages 33-45]
Javadirad, G. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Javadirad, G. Injection Optimization for Heavy Duty Diesel Engine in Order to Find High Efficiency and Low NOx Engine Concept by Means of Quasi Dimensional Multi-Zone Spray Modeling [Volume 22, Issue 22, 2011, Pages 29-38]
Javaheri, M. Design of Nondestructive System for Hardness of Carbonitrided Steel Parts âUsing Eddy Current Testing Method: Case study on the Tappet Parts [Volume 52, Issue 52, 2018, Pages 19-28]
Javan, S. Investigation of Effects of Spark Plugâs Electrodes Erosion on the Required Ignition Voltage and Performance of Natural Gas Engine [Volume 21, Issue 21, 2011, Pages 21-34]
Javan, S. Performance Evaluation of a Samand Vehicle with Internal Combustion Engine System and Hybrid Electric-Fuel Cell System [Volume 24, Issue 24, 2011, Pages 51-64]
Javan, S. Effect of electrode erosion on the required ignition voltage of spark plug in CNG spark ignition engine [Volume 26, Issue 26, 2012, Pages 31-39]
Javan, S. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Javan, S. Effect of starting temperature and belt width on lateral force of timing belt [Volume 48, Issue 48, 2017, Pages 13-18]
Javan, Saeed Development of Machine Vision System to Track Movement of an Engine Timing Belt Tensioner Based on Deep Neural Network [Volume 67, Issue 67, 2022, Pages 16-23]
Javanshayani, Faraz Machine Learning-Driven Modeling of Variable Valve Timing Effect on Fuel Consumption and Emission Reduction in a Turbocharged Port-Injection Engine [(Articles in Press)]
Jazayeri, A. Numerical Simulation of Direct Injection Engine with using Porous Media [Volume 23, Issue 23, 2011, Pages 45-58]
Jazayeri, S.A. Effect of Initial Temperature and EGR on Combustion and Performance Characteristics of Homogenous Charge Compression Ignition Engine Fueled with Dimethyl Ether [Volume 14, Issue 14, 2009, Pages 63-70]
Jazayeri, S.A. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Jazayeri, S.A. Performance Analysis of a Polymer Electrolyte Fuel Cell System for Automotive Application [Volume 16, Issue 16, 2009, Pages 3-15]
Jazayeri, S.A. Reducing of Transient Warm-up Period in an Internal Combustion Engine by Preheating of Engine Parts [Volume 17, Issue 17, 2010, Pages 15-27]
Jazayeri, S.A. Performance of Homogenous Charge Compression Ignition (HCCI) Engine with Premixed Methane/ Air Supported by DME for Electrical Power Generation Application [Volume 18, Issue 18, 2010, Pages 20-31]
Jazayeri, S.A. A Comprehensive Study on the Leading Factors Affecting on the Start of Combustion in a Homogenous Charge Compression Ignition (HCCI) Engine Fueled with Methane [Volume 20, Issue 20, 2010, Pages 69-79]
Jazayeri, S.A. Effect of Ambient Conditions and Fuel Composition on Fuel Consumption and NOx Emission Measurement for Vehicle in Driving Cycle [Volume 21, Issue 21, 2011, Pages 13-20]
Jazayeri, S.A. Injection Optimization for Heavy Duty Diesel Engine in Order to Find High Efficiency and Low NOx Engine Concept by Means of Quasi Dimensional Multi-Zone Spray Modeling [Volume 22, Issue 22, 2011, Pages 29-38]
Jazayeri, S.A. Using a single zone thermodynamic model in an HCCI engine to predict effective controlling parameters [Volume 25, Issue 25, 2012, Pages 13-23]
Jazayeri, S.A. Simulation of heat transfer considering boiling phenomenon in cooling passage of turbo-charged national engine [Volume 29, Issue 29, 2013, Pages 3-14]
Jazayeri, S.A. Study of spark ignition engine emissions fueled by blended hydrogen and methane [Volume 31, Issue 31, 2013, Pages 55-63]
Jazayeri, S.A. Developing a multi-zone thermo-kinetic model to investigate effects of using DME-methane blend in an HCCI engine [Volume 32, Issue 32, 2013, Pages 37-47]
Jazayeri, S.A. Investigation of combustion chamber thermal stratification effect on combustion performance of homogeneous charge compression ignition engine [Volume 35, Issue 35, 2014, Pages 3-16]
Jazayeri, Seyed Ali The Effect of Hydrogen Addition on a RCCI Engine Performance Fueled with Natural GasDiesel Fuel at Low Load Range [Volume 65, Issue 65, 2022, Pages 60-74]
Jenab, Kourosh Evaluation of reliability of diesel engine connecting rod by accelerated test method [Volume 64, Issue 64, 2021, Pages 41-53]
Joharchi, A. Experimental Investigation on the Effect of EGR Mixture Temperature on the Second Law Efficiency in Light-duty Diesel Engines [Volume 20, Issue 20, 2010, Pages 12-21]
K
Kakaee, A. H. Effects of piston bowl geometry on combustion and emissions characteristics of a natural gas/diesel RCCI engine [Volume 40, Issue 40, 2015, Pages 59-70]
Kakaee, A.H. Evaluation and Development of Methods for Knock Detection Using Cylinder Pressure Data [Volume 15, Issue 15, 2009, Pages 17-28]
Kakaee, A.H. Effect Investigation of Important Parameters in Knock Detection Using Cylinder Pressure Data [Volume 17, Issue 17, 2010, Pages 3-14]
Kakaee, A.H. Thermal Analysis of an SI Engine Piston Using Different Thermal Model [Volume 17, Issue 17, 2010, Pages 28-41]
Kakaee, A.H. Intake Manifold Optimization of XU7 Engine to Improve Volumetric Efficiency [Volume 20, Issue 20, 2010, Pages 3-11]
Kakaee, Amirhasan Powertrain mounting system optimization to improve vibration behavior for EF7 engine [Volume 53, Issue 53, 2019, Pages 55-68]
Kakaee, Amirhasan Increasing waste heat recovery from an internal combustion engine by a dual-loop non-organic Rankine Cycle [Volume 57, Issue 57, 2020, Pages 15-26]
Kakai, A.H. The Effect of Using Variable Valve System on XU7/L3 Engine [Volume 21, Issue 21, 2011, Pages 58-72]
Kalantari, Mahdi Enhancing the performance of a vapor compression refrigeration cycle by modifying the manufacturing process of the SLHX heat exchanger: transition from tangential to concentric configuration [Volume 72, Issue 2, 2025, Pages 19-30]
Kamarkhani, S. Muffler Design with Baffle Effect and Perforations on Transmission Loss [Volume 47, Issue 47, 2017, Pages 47-52]
Kamyab, Mohamad Investigating the effect of the coating process on improving the quality of mechanical bonding in the casting of aluminum cylinder block with cast-in iron liner [Volume 70, Issue 2, 2023, Pages 80-98]
Kanani, Javad The output performance of the 25% gasoline-75% NG combination mode and its comparison with NG mode [Volume 71, Issue 1, 2024, Pages 40-51]
Karami, P Thermodynamic Analysis of a Turboprop Engine Equipped With Solid Oxide Fuel Cell [Volume 62, Issue 62, 2021, Pages 55-63]
Karamian Manesh, Mohammad Javad Fuel consumption-aware powertrain selection and optimization for a B-class sedan [Volume 69, Issue 69, 2022, Pages 12-20]
Karbasiforoshha, M. Using predictive combustion model in combustion modeling of cooled EGR turbocharged engine [Volume 25, Issue 25, 2012, Pages 57-67]
Karbasiforushha, M. Effect of Ambient Conditions and Fuel Composition on Fuel Consumption and NOx Emission Measurement for Vehicle in Driving Cycle [Volume 21, Issue 21, 2011, Pages 13-20]
Kargarian Marvasti, Ahmadreza Investigating the performance and emission of RCCI engines with different compositions and percentages of natural gas [Volume 71, Issue 1, 2024, Pages 16-39]
Karimyan, A. Muffler Design with Baffle Effect and Perforations on Transmission Loss [Volume 47, Issue 47, 2017, Pages 47-52]
Kashi, Seyed Sajad Utilization of Stirling engine to improve the performance and fuel consumption of an internal combustion engine by exhaust gas heat recovery [Volume 66, Issue 66, 2022, Pages 68-84]
Kavand, M. Investigating the effect of nanocoating on friction loss and abrasion in the piston rings [Volume 53, Issue 53, 2019, Pages 13-22]
Kazemi, M. Prediction Oil Parameter of Connecting Rod Small End Bearing of EF7 Engine by Using Artificial Neural Network by Simulation in AVL Excite Software [Volume 20, Issue 20, 2010, Pages 22-29]
Kazemi, M. Simulation of vibration for a diesel engine with biodiesel and diesel fuel blends using artificial neural networks [Volume 23, Issue 23, 2011, Pages 22-31]
Kazemi, M. Health monitoring and performance investigation of accessory belt in an internal combustion engine during critical speeds [Volume 25, Issue 25, 2012, Pages 3-12]
Kazemi, M. Experimental and numerical investigation of stress in engine crankshaft [Volume 32, Issue 32, 2013, Pages 29-36]
Kazemi, M. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Kazemi, M. Root causes failure analysis of exhaust manifold heat shield failure [Volume 34, Issue 34, 2014, Pages 29-39]
Kazemi, Mohammad Vibration analysis of turbocharger in different clogging conditions of Diesel Particle Filter (DPF) [Volume 70, Issue 1, 2023, Pages 66-90]
Kazemi, Mohammad Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Kazempoor, P. Performance Evaluation of a Samand Vehicle with Internal Combustion Engine System and Hybrid Electric-Fuel Cell System [Volume 24, Issue 24, 2011, Pages 51-64]
Kazemzadeh Hannani, S. Numerical simulation of in-cylinder tumble flow field measurements and comparison to experimental results [Volume 26, Issue 26, 2012, Pages 11-19]
Keshavarz, A. Experimental Study of Hydrogen Addition Impact on Emissions and Performance of a Natural Gas Fueled Engine [Volume 14, Issue 14, 2009, Pages 43-50]
Keshavarz, A. Heat Balance of a Natural Gas Fueled Spark Ignition Engine with a Turbocharger [Volume 20, Issue 20, 2010, Pages 45-58]
Keshavarz, A. Integration of exhaust manifold with engine cylinder head towards size and weight reduction [Volume 30, Issue 30, 2013, Pages 55-65]
Keshavarz, A. Simulation of Subcooled Flow Boiling Occurring in Internal Combustion Engine Water Jacket by Numerical Modeling in a Channel with Hot Spot [Volume 53, Issue 53, 2019, Pages 23-32]
Keshavarz, M. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Keshavarz, M. Performance of Homogenous Charge Compression Ignition (HCCI) Engine with Premixed Methane/ Air Supported by DME for Electrical Power Generation Application [Volume 18, Issue 18, 2010, Pages 20-31]
Keshavarz, M. Injection Optimization for Heavy Duty Diesel Engine in Order to Find High Efficiency and Low NOx Engine Concept by Means of Quasi Dimensional Multi-Zone Spray Modeling [Volume 22, Issue 22, 2011, Pages 29-38]
Keshavarzi, Ali Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Kettner, Maurice Experimental investigations on a pre-chamber spark plug with variable heat range by integrating a controlled hot surface [Volume 69, Issue 69, 2022, Pages 3-11]
Khabbaz, S.A. Theoretical Investigation of the Effect of Injection Pressure, Duration and Time Injection on Combustion, Performance and Emission Characteristics of a DI Diesel Engine [Volume 19, Issue 19, 2010, Pages 49-63]
Khaleghinia, Jahanfar The Effect of Hydrogen Addition on a RCCI Engine Performance Fueled with Natural GasDiesel Fuel at Low Load Range [Volume 65, Issue 65, 2022, Pages 60-74]
Khalesi, Mohammad Hossein Investigating the effects of geographics climate on the characteristics of statistical data and driving cycle [Volume 70, Issue 2, 2023, Pages 37-65]
Khalilarya, S. Investigation of combustion and emissions of natural gas-diesel dual-fuel PPCI engine [Volume 41, Issue 41, 2016, Pages 13-19]
Khalilarya, Shahram Experimental investigation and simulation of lean burn combustion in a SI natural gas engine using prechambered spark plug [Volume 50, Issue 50, 2018, Pages 41-54]
Khalili, A.R. Effect of combustion products of gasoline-ethanol blended fuel on corrosion of valve and cylinder head alloys of SI engines [Volume 28, Issue 28, 2012, Pages 3-10]
Khalilzadeh, M. Simulating and prototyping of a compression ring for diesel engine regarding required spring back force [Volume 32, Issue 32, 2013, Pages 21-28]
Khanaki, Amirhossein The Effect of Injection Timing and Phasing on the Emission of a Gasoline Single Cylinder Engine [Volume 65, Issue 65, 2022, Pages 3-20]
Khanali, J. Muffler Design with Baffle Effect and Perforations on Transmission Loss [Volume 47, Issue 47, 2017, Pages 47-52]
Khani, M. Numerical Simulation of Combustion Process of Biodiesel and Diesel Blending in a Compression Ignition Engine [Volume 19, Issue 19, 2010, Pages 19-28]
Khatamnejad, H. Principle of valves timing optimization in D87 diesel to premixed natural gas engine conversion [Volume 49, Issue 49, 2018, Pages 65-76]
Khatamnezhad, H. Investigation of combustion and emissions of natural gas-diesel dual-fuel PPCI engine [Volume 41, Issue 41, 2016, Pages 13-19]
Khazaee, M. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Khazaee, M. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Khazaee, Meghdad The study on effect of different defects on the timing belt vibrations using data mining and artificial intelligence methods [Volume 36, Issue 36, 2014, Pages 61-70]
Khazaee, Meghdad Detection and classification of mechanical faults of an engine alternator based on vibration signals and frequency analysis [Volume 61, Issue 61, 2021, Pages 3-10]
Khazaee, Meghdad Investigation of performance and exhaust emission of diesel engine in different ratios of lambda coefficient using diesel-ethanol fuel blends [Volume 60, Issue 60, 2020, Pages 19-28]
Kheybari, M. Muffler Design with Baffle Effect and Perforations on Transmission Loss [Volume 47, Issue 47, 2017, Pages 47-52]
Khodaei, R. A comparative study of effect of valve overlap on HCCI engines [Volume 32, Issue 32, 2013, Pages 3-12]
Khorasani, Milad Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Khorramirad, Vahid Investigation on the effect of using electric supercharging on the performance of a SI-TC engine [Volume 43, Issue 43, 2016, Pages 41-54]
Khorramirad, Vahid Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Khorrami Rad, Vahid Designing Nonlinear Digital Controller for Switching Non Affine Process of Spark Ignition Engine Catalyst Warm-Up [Volume 65, Issue 65, 2022, Pages 42-59]
Khoshbakhti Saray, R Development of a predictive Model for start of combustion of a reactivity-controlled compression ignition engine [Volume 62, Issue 62, 2021, Pages 3-13]
Khoshbakhti Saray, R. Theoretical Investigation of Combustion Process in Dual Fuel Engines at Part Load Considering the Effect of Exhaust Gas Recirculation [Volume 14, Issue 14, 2009, Pages 51-62]
Khoshbakhti Saray, R. Theoretical Investigation of the Effect of Injection Pressure, Duration and Time Injection on Combustion, Performance and Emission Characteristics of a DI Diesel Engine [Volume 19, Issue 19, 2010, Pages 49-63]
Khoshbakhti Saray, R. A comparative study of effect of valve overlap on HCCI engines [Volume 32, Issue 32, 2013, Pages 3-12]
Khoshbakhti Saray, R. Modeling of HCCI combustion and emissions using a multi-zone model [Volume 33, Issue 33, 2014, Pages 13-21]
Khoshbakhti Saray, R. Investigation on the effect of reformer gas addition on HCCI combustion of blended fuel [Volume 40, Issue 40, 2015, Pages 23-33]
Khoshbakhti Saray, Rahim Development of a zero-dimensional turbulence model for the flow field of spark-ignition engines, considering vortex motions, based on a new approach [Volume 71, Issue 4, 2025, Pages 77-101]
Khoshbakhti Saray, Rahim Optimizing the shape of the ULPC combustion chamber for a diesel engine equipped with a common rail fuel injection system [(Articles in Press)]
Khoshnam, Farhad Evaluating the coupled thermo-mechanical stresses for an aluminum alloy piston used in a gasoline engine XU7 [Volume 42, Issue 42, 2016, Pages 33-42]
Khoshnam, Farhad Numerical investigation on Effect of thermally isolated piston on improving SI engine performance during the cold start conditions [Volume 47, Issue 47, 2017, Pages 3-12]
Khosravi, K. Integration of exhaust manifold with engine cylinder head towards size and weight reduction [Volume 30, Issue 30, 2013, Pages 55-65]
Khosravian, Erfan Simulation and prediction of bubble dynamic parameters using machine learning algorithm in boiling process used in thermal analysis of internal combustion engines [Volume 70, Issue 2, 2023, Pages 99-117]
Kiani, Mostafa The Effect of throttle valve positions on thermomechanical exergy, burned fuel exergy, exergy with heat transfer and exergy with work transfer of an SI Engine [Volume 43, Issue 43, 2016, Pages 31-40]
Kiani Deh Kiani, M. Modeling of an SI engine performance parameters and emissions using bio-ethanol-gasoline blends by genetic programming [Volume 27, Issue 27, 2012, Pages 47-57]
KianiMajd, Mehdi Development of an electrochemical deburring process using ultrasonic waves for combustion engine oil spring ring [Volume 71, Issue 2, 2024, Pages 55-68]
Kirchberger, Roland Experimental investigations on a pre-chamber spark plug with variable heat range by integrating a controlled hot surface [Volume 69, Issue 69, 2022, Pages 3-11]
Koochak, M. Heat Balance of a Natural Gas Fueled Spark Ignition Engine with a Turbocharger [Volume 20, Issue 20, 2010, Pages 45-58]
Kordi, M. Axial vane rotary engines preliminary design by quasi dimensional modeling technique [Volume 41, Issue 41, 2016, Pages 41-53]
L
Lashkarpour, S.M Development of a predictive Model for start of combustion of a reactivity-controlled compression ignition engine [Volume 62, Issue 62, 2021, Pages 3-13]
Lashkarpour, S.M. Determination of PM and NOx Pollutants Correction Factors in IC Diesel Engines Related to sea level Condition [Volume 21, Issue 21, 2011, Pages 48-57]
Lashkarpour, S.M. Enhancement of a Diesel Engine Inlet Port for Pollutant Reduction and Performance Optimization [Volume 22, Issue 22, 2011, Pages 39-49]
Lashkarpour, S.M. Optimizing the shape of the ULPC combustion chamber for a diesel engine equipped with a common rail fuel injection system [(Articles in Press)]
Lee, S. Y. Inspection of Impurity effects on the methane laminar flame speed under lean and diluted conditions [Volume 47, Issue 47, 2017, Pages 21-30]
Lekzian, Elyas Gasification of petroleum and chemical base fuels with the aim of hydrogen-rich syngas [Volume 70, Issue 3, 2023, Pages 30-38]
Lekzian, Elyas Aerothermodynamic off-design performance study of a fixed double bypass duct turbofan engine [Volume 70, Issue 3, 2023, Pages 62-75]
Lori Alikhani, Hossein Simulation of cylinder deactivation and its effects on emission and fuel consumption [Volume 71, Issue 1, 2024, Pages 79-90]
M
Madadi, Ali Simulation and scale-up of a centrifugal compressor for a turbocharger of a lean combustion engine employing 1-D and 3-D design and geometrical modification of the impeller [Volume 66, Issue 66, 2022, Pages 22-35]
Madani, Navid Design of Intelligent Cooling System with electrical Thermostat and Implementation of Strategy in Engine Control Unit [Volume 43, Issue 43, 2016, Pages 55-62]
Madani, Seyed Navid Sensitivity analysis for objectives of power, efficiency, heat loss, and working fluid cost based on input parameters in the Stirling engine [Volume 70, Issue 2, 2023, Pages 1-21]
Mafakheri, Meysam Simulation of cylinder deactivation and its effects on emission and fuel consumption [Volume 71, Issue 1, 2024, Pages 79-90]
Mafakheri, Meysam Simulation of the Effect of Using a Turbocharger on XU7 Engine Performance with Mechanical and Electronic Wastegate Control Mechanisms [(Articles in Press)]
Mafi, A. Failure analysis of an intake valve in a gasoline engine [Volume 26, Issue 26, 2012, Pages 3-9]
Mafi, A. Failure analysis of a dynamometer drive shaft coupled to an engine [Volume 30, Issue 30, 2013, Pages 37-46]
Mafi, A. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Mafi, A. Root causes failure analysis of exhaust manifold heat shield failure [Volume 34, Issue 34, 2014, Pages 29-39]
Maghsoudi, Mahdi Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Maghsoudi Gharehbolagh, Ghasem Simulation of torsional vibrations of dual mass flywheel in a 3-cylinder engine [Volume 70, Issue 1, 2023, Pages 1-13]
Maghsoudi Mehraban, Karim Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Maghsoudi Mehrban, Karim Simulation and performance analysis of a high-energy-density lithium–sulfur battery under cold start and standard european driving cycle conditions in an electric vehicle [Volume 72, Issue 3, 2025, Pages 24-42]
Mahdavian, Alireza Vibration analysis of turbocharger in different clogging conditions of Diesel Particle Filter (DPF) [Volume 70, Issue 1, 2023, Pages 66-90]
Mahdavy Moghaddam, H. Thermal analysis of functionally graded materials in cylinders and pistons based on super element method [Volume 30, Issue 30, 2013, Pages 25-36]
Mahdiyar, N Modeling of Motor Oil Containing Diamond Nanoparticle Between two Iron Abrasion Surfaces Using Molecular Dynamics Methods [Volume 62, Issue 62, 2021, Pages 31-41]
Mahmoodi, M Thermodynamic Analysis of a Turboprop Engine Equipped With Solid Oxide Fuel Cell [Volume 62, Issue 62, 2021, Pages 55-63]
Mahmoodi, Reza Study on the effect of using reformed biogas as a low reactivity fuel in a dual-fuel engine (RCCI) [Volume 59, Issue 59, 2020, Pages 73-93]
Mahmoudi, A.A. Effect Investigation of Important Parameters in Knock Detection Using Cylinder Pressure Data [Volume 17, Issue 17, 2010, Pages 3-14]
Mahmoudi, A.A. Steady-state modeling of a turbocharger in gasoline engines [Volume 26, Issue 26, 2012, Pages 21-30]
Malayeri, Mohammadreza Investigation of particulate fouling in exhaust gas recirculation coolers in diesel engines [Volume 37, Issue 37, 2015, Pages 49-64]
Malekan, Ali Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Malekbala, M.R. Performance Evaluation of a Samand Vehicle with Internal Combustion Engine System and Hybrid Electric-Fuel Cell System [Volume 24, Issue 24, 2011, Pages 51-64]
Maleki, A. Influence of cylinder deactivation technology on fuel consumption and emissions of four-cylinder spark ignition engine [Volume 35, Issue 35, 2014, Pages 41-51]
Malekpoor, Mohammad Optimizing the shape of the ULPC combustion chamber for a diesel engine equipped with a common rail fuel injection system [(Articles in Press)]
Mamat, Rizalman Investigation of Blended Palm Biodiesel-Diesel Fuel Properties with Water Emulsification [Volume 57, Issue 57, 2020, Pages 65-74]
Marami Milani, S. Enhancement of a Diesel Engine Inlet Port for Pollutant Reduction and Performance Optimization [Volume 22, Issue 22, 2011, Pages 39-49]
Marbout, Armin Optimization of solution temperature and time in nickel-based super-alloy of engine turbo-charger based on hardness by design of experiments [Volume 43, Issue 43, 2016, Pages 63-70]
Mardan, Ehsan Concept selection for engine components using the DEMATEL-ANP-TOPSIS combination method: case study for cam bearing frame part [Volume 61, Issue 61, 2021, Pages 61-71]
Mardani, Ershad Gasification of petroleum and chemical base fuels with the aim of hydrogen-rich syngas [Volume 70, Issue 3, 2023, Pages 30-38]
Marzban, M. Health monitoring and performance investigation of accessory belt in an internal combustion engine during critical speeds [Volume 25, Issue 25, 2012, Pages 3-12]
Mashadi, B. Performance Enhancement of Hybrid Eclectic Vehicles by Introduction of a Novel Power Split Device [Volume 15, Issue 15, 2009, Pages 36-44]
Mashadi, B. Influence of cylinder deactivation technology on fuel consumption and emissions of four-cylinder spark ignition engine [Volume 35, Issue 35, 2014, Pages 41-51]
Mashadi, Behrooz Powertrain mounting system optimization to improve vibration behavior for EF7 engine [Volume 53, Issue 53, 2019, Pages 55-68]
Mashhadi, Behrooz Increasing waste heat recovery from an internal combustion engine by a dual-loop non-organic Rankine Cycle [Volume 57, Issue 57, 2020, Pages 15-26]
Masih Tehrani, Masoud Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Massah, Jafar Magnetizing the Perkins A63544 Engine Fuel and Its Vibratory Assessment [Volume 38, Issue 38, 2015, Pages 17-26]
Massah, Jafar Numerical investigation the effect of accumulator on reducing the pressure waves in a common rail fuel injection system of diesel engine [Volume 68, Issue 68, 2022, Pages 31-38]
Mazaheri, Hossein Improvement of hardness and tribology properties of engine parts by formation of surface composite layer containing alumina particles by using gas-tungsten arc welding process [Volume 43, Issue 43, 2016, Pages 3-12]
Mazaheri, Hossein Experimental investigation on the gamma model Stirling engine for cooling production using various gases [Volume 59, Issue 59, 2020, Pages 17-28]
Mazidi, Mohammad The Thermal Simulation of an Exhaust Valve and its Seat Using Thermal Contact Conductance Obtained from the Inverse Solution [Volume 36, Issue 36, 2014, Pages 27-38]
Meccariello, Giovanni Characterization of High-pressure Hydrogen Jet for ICE in terms of Morphology and Flow-rates [Volume 70, Issue 4, 2024, Pages 27-39]
Meghdadi, , Amir Homayoon Experimental study of porous medium effect on pollutant emissions and fuel consumption for motorcycles [Volume 45, Issue 45, 2017, Pages 53-62]
Mehdigholi, H. Piston Scuffing Detection by Acoustic Emission Method [Volume 24, Issue 24, 2011, Pages 21-28]
Mehdigholi, H. Valve fault diagnosis in internal combustion engines by acoustic emission method using artificial neural network [Volume 27, Issue 27, 2012, Pages 11-21]
Mehdipour, R. Simulation of Heat Transfer in the Cooling Passages of the âEF7â Engine Considering Boiling Phenomenon [Volume 19, Issue 19, 2010, Pages 64-73]
Mehdipour, R. Mathematical simulation of a vehicle radiator by genetic algorithm method and comparison with experimental data [Volume 30, Issue 30, 2013, Pages 15-23]
Mehmandoust, Babak Experimental study of porous medium effect on pollutant emissions and fuel consumption for motorcycles [Volume 45, Issue 45, 2017, Pages 53-62]
Mehrabbi Vaghar, M. Effect of oil viscosity on rings and pistons friction using experimental tests and semi-empirical equations in the motoring mode [Volume 48, Issue 48, 2017, Pages 41-48]
Mehrabi V., M. Simulation of piston and ring friction at the motoring condition and investigation effect of combustion and clearance between the piston and cylinder [Volume 39, Issue 39, 2015, Pages 41-48]
Mehrabivaghar, M. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Mehrabi Vaghar, Mojtaba Experimental and Analytical Investigation of the Oil Viscosity Effect on Vertical Vibrations of a CI Engine [Volume 46, Issue 46, 2017, Pages 65-74]
Mehrabi Vaghar, Mojtaba Experimental investigation of the effect of modifying the engine cooling circuit with the aim of improving the temperature of the cylinder head and block [Volume 71, Issue 3, 2024, Pages 45-55]
Mehrjou, Habibollah Thermal Investigation of turbocharger using infra-red camera [Volume 50, Issue 50, 2018, Pages 3-16]
Mehrkish, A. A study on side effects of cooling in a new active multi-compartment mount [Volume 29, Issue 29, 2013, Pages 25-38]
Mehrkish, A. Study on effect of electric/combustion engine on performance of a parallel hybrid vehicle and proposing engine selection algorithm [Volume 31, Issue 31, 2013, Pages 21-31]
Mehvari, Reza Comparison between revolution sensor by using PVDF sensor in XU7 engine and vibration energy harvesting [Volume 44, Issue 44, 2016, Pages 3-18]
Mian Zarasvand, Fatemeh Numerical Simulation Effect of EHC on CO Emission in Cold-Start Conditions of a Motorcycle Engine [Volume 44, Issue 44, 2016, Pages 43-52]
Mighani, Naser Development of balance shaft and flywheel for single cylinder diesel engine based on analytical approach and comparison with the simulation result [Volume 51, Issue 51, 2018, Pages 63-74]
Minaei, Saeid The study on effect of different defects on the timing belt vibrations using data mining and artificial intelligence methods [Volume 36, Issue 36, 2014, Pages 61-70]
Mir Fatahi, Arman Utilization of internal heat exchanger in air condition pipe at automotive industry [Volume 72, Issue 2, 2025, Pages 1-8]
Miri, Seyed Mohammadreza Functional Variables of a Biodiesel-Powered Single-Cylinder Diesel Engine: an Experimental Analysis [Volume 38, Issue 38, 2015, Pages 49-60]
Mirmohammadi, A Experimental study of the use of oxygenated Ethanol and Diisopropyl ethercomponeds in gasoline fuel and their effects ontheXU7JP/L3 engine performance and emissions [Volume 63, Issue 63, 2021, Pages 13-21]
Mirmohammadi, Ali Investigating the performance and emission of RCCI engines with different compositions and percentages of natural gas [Volume 71, Issue 1, 2024, Pages 16-39]
Mirsalim, M. Laminar flame speed measurement and correlation for methane-iso-octane fuel blend [Volume 39, Issue 39, 2015, Pages 11-20]
Mirsalim, M. Investigation of combustion and emissions of natural gas-diesel dual-fuel PPCI engine [Volume 41, Issue 41, 2016, Pages 13-19]
Mirsalim, Mostafa The study on effect of different defects on the timing belt vibrations using data mining and artificial intelligence methods [Volume 36, Issue 36, 2014, Pages 61-70]
Mirsalim, Mostafa Effect of fuel injection discharge curve and injection pressure on upgrading power and combustion parameters in HD diesel engine with CFD simulation [Volume 42, Issue 42, 2016, Pages 3-12]
Mirsalim, Mostafa Experimental investigation and simulation of lean burn combustion in a SI natural gas engine using prechambered spark plug [Volume 50, Issue 50, 2018, Pages 41-54]
Mirsalim, Mostafa Developing a reduced chemical kinetic mechanism for natural gas/biodiesel mixture combustion [Volume 71, Issue 4, 2025, Pages 15-32]
Mirsalim, Seyed Mostafa A Numerical Study on Non-Reacting Spray Characteristics of Different Marine Diesel Fuel-Water Emulsion Blends [Volume 44, Issue 44, 2016, Pages 65-77]
Mirsalim, Seyyed Mostafa Evaluation of reliability of diesel engine connecting rod by accelerated test method [Volume 64, Issue 64, 2021, Pages 41-53]
Mirsalim, S. M. Experimental investigation on the effect of injection pressure and injector installation angle on the penetration of the gasoline port fuel injector using high speed imaging method [Volume 52, Issue 52, 2018, Pages 29-42]
Mirsalim, S.M. Investigation of Swirling and Tumbling Flow Pattern of Spark Ignition Engine [Volume 14, Issue 14, 2009, Pages 27-34]
Mirsalim, S.M. The Effect of Different Injection Configuration on Combustion and Emissions Formation in a Heavy Duty Diesel Engine [Volume 16, Issue 16, 2009, Pages 43-51]
Mirsalim, S.M. Investigation on the Effect of the Cooling Jet Impacts on the Moving Piston on Produced Oil Droplets Using a Motored Engine [Volume 19, Issue 19, 2010, Pages 38-48]
Mirsalim, S.M. Heat Balance of a Natural Gas Fueled Spark Ignition Engine with a Turbocharger [Volume 20, Issue 20, 2010, Pages 45-58]
Mirsalim, S.M. Experimental investigation on the pumping loss and pressure oscillations in the crankcase [Volume 23, Issue 23, 2011, Pages 3-10]
Mirsalim, S.M. Determination of knock borderline ignition timing in turbocharged spark ignition engines [Volume 27, Issue 27, 2012, Pages 33-45]
Mirsalim, S.M. Experimental investigation of the effect of pressure and density ratio on the gaseous spray of the group-hole nozzle [Volume 28, Issue 28, 2012, Pages 11-19]
Mirsalim, S.M. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Mirsalim, S.M. Diagnosis and classification of effective abnormal environmental conditions on timing belt performance based on vibration signals [Volume 31, Issue 31, 2013, Pages 33-41]
Mirsalim, S.M. Numerical study of effect of ambient backpressure and temperature on spray characteristics of heavy fuel oil/n-butanol blend [Volume 31, Issue 31, 2013, Pages 43-53]
Mirsalim, S.M. Sensitivity analysis of parameters affecting image processing of high pressure gaseous jet images [Volume 33, Issue 33, 2014, Pages 43-52]
Mirsalim, S.M. Numerical investigation of non-reacting spray characteristics of heavy âfuel and alternative fuel under high injection pressure [Volume 34, Issue 34, 2014, Pages 3-15]
Mirsalim, S.M. Knock detection based on main vibration frequencies analysis in spark âignition turbocharged engine [Volume 34, Issue 34, 2014, Pages 17-27]
Mirsalim, S.M. Investigation of combustion chamber thermal stratification effect on combustion performance of homogeneous charge compression ignition engine [Volume 35, Issue 35, 2014, Pages 3-16]
Mirsalim, S.M. Investigation of diesel fuel and soybean methyl esters emission in high-speed diesel engine [Volume 35, Issue 35, 2014, Pages 31-39]
Mirsalim, S.M. An experimental study of pre-main injection strategy to optimize TDI diesel engine [Volume 41, Issue 41, 2016, Pages 55-62]
Mirsane, Seyed Amirhossein Investigating the effect of bioethanol fuel concentration with different percentages on power and torque in EF7 engine [Volume 70, Issue 3, 2023, Pages 18-29]
Moazami Goodarzi, Mohammad Rasool Utilization of internal heat exchanger in air condition pipe at automotive industry [Volume 72, Issue 2, 2025, Pages 1-8]
Mobasherpour, Iman The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
Modanlou, Reza Aerothermodynamic off-design performance study of a fixed double bypass duct turbofan engine [Volume 70, Issue 3, 2023, Pages 62-75]
Modarres Razavi, S.M.R. Numerical Analysis of Injected EGR/Blowby Gases Distribution in Intake Manifold [Volume 15, Issue 15, 2009, Pages 55-65]
Moghadam, Ali Enhancing the performance of a vapor compression refrigeration cycle by modifying the manufacturing process of the SLHX heat exchanger: transition from tangential to concentric configuration [Volume 72, Issue 2, 2025, Pages 19-30]
Moghadam, F. Experimental and numerical investigation of stress in engine crankshaft [Volume 32, Issue 32, 2013, Pages 29-36]
Moghaddam, F. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Moghaddam, P. A framework for prioritizing improvement and development of engine [Volume 28, Issue 28, 2012, Pages 39-49]
Moghimi, Mohsen Fuel consumption optimization of a series hybrid electric vehicle utilizing fuzzy logic control [Volume 68, Issue 68, 2022, Pages 23-30]
Mohammadebrahim, A Investigation of the effect of design variables of a thermoelectric generator on fuel consumption and output power of a vehicle [Volume 63, Issue 63, 2021, Pages 35-47]
Mohammadebrahim, A. Intake Manifold Optimization of XU7 Engine to Improve Volumetric Efficiency [Volume 20, Issue 20, 2010, Pages 3-11]
Mohammadebrahim, A. Numerical simulation of in-cylinder tumble flow field measurements and comparison to experimental results [Volume 26, Issue 26, 2012, Pages 11-19]
Mohammadebrahim, A. Study of two-stage turbocharging for compensation of low-end torque [Volume 49, Issue 49, 2018, Pages 39-46]
Mohammadebrahim, Abolfazl Investigation of the in-cylinder swirl flow measurement methods and comparison between them in a cylinder head [Volume 42, Issue 42, 2016, Pages 51-58]
Mohammadebrahim, Abolfazl Investigation on the effect of using electric supercharging on the performance of a SI-TC engine [Volume 43, Issue 43, 2016, Pages 41-54]
Mohammadebrahim, Abolfazl Development of balance shaft and flywheel for single cylinder diesel engine based on analytical approach and comparison with the simulation result [Volume 51, Issue 51, 2018, Pages 63-74]
Mohammadebrahim, Abolfazl Simulation of a vehicle equipped with a proton exchange membrane fuel cell and investigating the effect of related parameters [Volume 70, Issue 1, 2023, Pages 28-46]
Mohammadebrahim, Abolfazl Verification of the performance of the paddle wheel swirl meter using numerical simulation and experimental test [Volume 70, Issue 4, 2024, Pages 40-55]
Mohammadi, A Numerical and Experimental Analysis of Flow Velocity in the Cylinder Head of Transparent Iranian National Engine with PIV Method [Volume 63, Issue 63, 2021, Pages 61-76]
Mohammadi, A. Two Phase Flow Simulation for Subcooled Nucleat Boiling Heat Transfer Calculation in Water Jacket of Diesel Engine [Volume 22, Issue 22, 2011, Pages 50-61]
Mohammadi, A. Numerical Simulation of Direct Injection Engine with using Porous Media [Volume 23, Issue 23, 2011, Pages 45-58]
Mohammadi, A. Simulation of heat transfer considering boiling phenomenon in cooling passage of turbo-charged national engine [Volume 29, Issue 29, 2013, Pages 3-14]
Mohammadi, A. Research on modification of cooling passage for a 4-cylinder turbo-charged SI engine with precise cooling view point [Volume 41, Issue 41, 2016, Pages 31-39]
Mohammadi, A. Effect of tumble flap on combustion and performance of NA national engine [Volume 49, Issue 49, 2018, Pages 3-18]
Mohammadi, A. Thermal Analysis of Turbocharger Steel Gasket via Experimental Test [Volume 53, Issue 53, 2019, Pages 33-44]
Mohammadi, Arash Experimental investigation on the gamma model Stirling engine for cooling production using various gases [Volume 59, Issue 59, 2020, Pages 17-28]
Mohammadi, Arash Numerical investigation of the parameters of a prismatic lithium ion battery under load for electrical vehicle [Volume 59, Issue 59, 2020, Pages 45-62]
Mohammadi, Arash Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Mohammadi, Arash CFD simulation of wall film during fuel injection and combustion in a three-cylinder turbocharged gasoline direct injection engine [Volume 70, Issue 4, 2024, Pages 1-13]
Mohammadi, Arash Reduction of fuel consumption and emissions of Iranian naturally aspirated engine on Samand vehicle with thermal management [Volume 71, Issue 4, 2025, Pages 58-76]
Mohammadi, Arash Simulation of fuel consumption of a hydrogen fuel cell electric vehicle with a thermostat control strategy and variables affecting its fuel consumption in ADVISOR software [Volume 72, Issue 3, 2025, Pages 85-105]
Mohammadi, Arash Simulation and performance analysis of a high-energy-density lithium–sulfur battery under cold start and standard european driving cycle conditions in an electric vehicle [Volume 72, Issue 3, 2025, Pages 24-42]
Mohammadi, F. Thermo-Mechanical Fatigue Life Assessment of Diesel Engine Hot Components [Volume 23, Issue 23, 2011, Pages 59-71]
Mohammadi Aghdam, M. Study of Effects of Combustion Gases and Cooling Thermal Boundary Conditions on Temperature Distribution of a Heavy Duty Diesel Engine Cylinder Head [Volume 17, Issue 17, 2010, Pages 71-81]
Mohammadian, A. Evaluation of Changes in Soot Formation with Variation of Start Angle of Fuel Injection in Diesel Engine [Volume 24, Issue 24, 2011, Pages 37-49]
Mohammadsadeghi, Farshad Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Mohammadzadeh, A. Thermal analysis of functionally graded materials in cylinders and pistons based on super element method [Volume 30, Issue 30, 2013, Pages 25-36]
Mohebbi, M. Experimental investigation of gasoline fueled HCCI engine load expansion [Volume 39, Issue 39, 2015, Pages 3-10]
Mohebbi, Mohamad Sadiq Investigating of Process Design Parameters in 4043 alloy Additive Manufactured specimens, to create external features of cylinder head [Volume 60, Issue 60, 2020, Pages 3-17]
Mohsenirad, M. An experimental investigation of the influence of diluent gas on laminar flame speed of natural gas and gasoline fuel mixture [Volume 40, Issue 40, 2015, Pages 47-57]
Mohsenirad, M. Effect of tumble flap on combustion and performance of NA national engine [Volume 49, Issue 49, 2018, Pages 3-18]
Mohsenirad, M. Port Development of a Port Injection Turbocharged Engine to Improve Combustion Quality & Performance Parameters [Volume 49, Issue 49, 2018, Pages 47-66]
Mohsenirad, Mohsen Conceptual and experimental study of an Atkinson cycle engine of a Series-Parallel hybrid electric vehicle [Volume 70, Issue 4, 2024, Pages 69-80]
Mohtadi Bonab, Mohammad Ali Experimental analysis of the effect of using aluminum oxide nanofluid in improving the heat transfer of XU7 engine radiator [Volume 70, Issue 2, 2023, Pages 66-79]
Mohtasebi, S.S. Simulation of vibration for a diesel engine with biodiesel and diesel fuel blends using artificial neural networks [Volume 23, Issue 23, 2011, Pages 22-31]
Mohtasebi, S.S. Effects of Nano-Particles on Properties of Engine Oil and its Functionality Rate on Wear Reduction [Volume 24, Issue 24, 2011, Pages 3-12]
Mojaddam, Mohammad Investigation of the Effect of the Geometric Deviations on the Performance of a Radial Flow Compressor Employing Uncertainty Quantification (UQ) and Sensitivity Analysis [Volume 67, Issue 67, 2022, Pages 51-63]
Mokhtari Shirazabad, M. An Investigation of High Cycle Fatigue Behavior of Magnesium Alloy for Cylinder Head Application [Volume 24, Issue 24, 2011, Pages 29-35]
Molaei, A. Port Development of a Port Injection Turbocharged Engine to Improve Combustion Quality & Performance Parameters [Volume 49, Issue 49, 2018, Pages 47-66]
Molaei Raoof, Zahra Fuel consumption-aware powertrain selection and optimization for a B-class sedan [Volume 69, Issue 69, 2022, Pages 12-20]
Molazem, M. Stress intensity factor in single cracked gears made of steel and functionally graded materials in vehicle gearbox [Volume 29, Issue 29, 2013, Pages 47-56]
Mollaei, B. Investigation of effect of adding natural gas on gasoline laminar flame speed [Volume 32, Issue 32, 2013, Pages 49-57]
Mollaei, B. Laminar flame speed measurement and correlation for methane-iso-octane fuel blend [Volume 39, Issue 39, 2015, Pages 11-20]
Mollaei, B. An experimental investigation of the influence of diluent gas on laminar flame speed of natural gas and gasoline fuel mixture [Volume 40, Issue 40, 2015, Pages 47-57]
Momeni Movahed, M. Evaluation and Development of Methods for Knock Detection Using Cylinder Pressure Data [Volume 15, Issue 15, 2009, Pages 17-28]
Momeni Movahed, M. Effect Investigation of Important Parameters in Knock Detection Using Cylinder Pressure Data [Volume 17, Issue 17, 2010, Pages 3-14]
Momeni Movahed, M. Determination of knock borderline ignition timing in turbocharged spark ignition engines [Volume 27, Issue 27, 2012, Pages 33-45]
Momeni Movahed, M. Knock detection based on main vibration frequencies analysis in spark âignition turbocharged engine [Volume 34, Issue 34, 2014, Pages 17-27]
Momeni Movahed, Mohammad Development of optimized model for filter and integrator of knock detection integrated circuit in automotive engine management system [Volume 37, Issue 37, 2015, Pages 65-74]
Monemian, E. Hydrogen and Oxygen Fuel Enrichment Effects on a HD Diesel Engine [Volume 47, Issue 47, 2017, Pages 13-20]
Monfaredi, M. An experimental study of pre-main injection strategy to optimize TDI diesel engine [Volume 41, Issue 41, 2016, Pages 55-62]
Montanaro, Alessandro Air-fuel Mixture Preparation for Internal Combustion Engines:Optical Techniques for Diagnosis of the Spray Developments [Volume 57, Issue 57, 2020, Pages 51-64]
Montanaro, Alessandro Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
Montanaro, Alessandro Characterization of High-pressure Hydrogen Jet for ICE in terms of Morphology and Flow-rates [Volume 70, Issue 4, 2024, Pages 27-39]
Montazer, Yaghoub Reduction of fuel consumption and emissions of Iranian naturally aspirated engine on Samand vehicle with thermal management [Volume 71, Issue 4, 2025, Pages 58-76]
Montazeri, M. Simulation of Fuel Consumption and Exhaust Emissions in Dual Fuel Samand Vehicle and Verification with NEDC Modal Test Results [Volume 15, Issue 15, 2009, Pages 11-16]
Montazeri, M. Driving Features and Their Influences on Hybrid Electric Vehicleâs Fuel Consumption and Exhaust Emissions [Volume 17, Issue 17, 2010, Pages 42-51]
Montazeri, M. Simulation of the Double Sided Clutch AMT and Investigation of Itâs Effect on HEV Performance [Volume 21, Issue 21, 2011, Pages 3-12]
Moosaie, A. A study of contact heat transfer problem in exhaust valve of internal âcombustion engines [Volume 34, Issue 34, 2014, Pages 51-60]
Moosavian, Ashkan Detection and classification of mechanical faults of an engine alternator based on vibration signals and frequency analysis [Volume 61, Issue 61, 2021, Pages 3-10]
Moosavian, Ashkan The Machine Vision Approach as a Poka-Yoke System in Conrod Bearing Assembly Station of Engine Production Line [Volume 65, Issue 65, 2022, Pages 88-99]
Moosavian, Ashkan Development of Machine Vision System to Track Movement of an Engine Timing Belt Tensioner Based on Deep Neural Network [Volume 67, Issue 67, 2022, Pages 16-23]
Moosavian, Ashkan Investigating the effects of geographics climate on the characteristics of statistical data and driving cycle [Volume 70, Issue 2, 2023, Pages 37-65]
Moosavian, Ashkan Automatic intelligent inspection system for crankshaft grade detection based on machine vision and deep learning [Volume 71, Issue 4, 2025, Pages 33-43]
Moosavian, Ashkan Convolutional transformer approach for engine spark plug fault diagnosis using acoustic signal [Volume 70, Issue 4, 2024, Pages 56-68]
Moosavian, Ashkan Defect detection in piston rings using deep learning-based computer vision [Volume 72, Issue 2, 2025, Pages 9-18]
Moosavian, Ashkan Acoustic signal-based misfire detection in internal combustion engines using machine learning techniques [(Articles in Press)]
Moosavian, S.A. Health monitoring and performance investigation of accessory belt in an internal combustion engine during critical speeds [Volume 25, Issue 25, 2012, Pages 3-12]
Moosavian, S.A. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Moosavian, S.A. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Moosavian, Seyed Ashkan Investigation of performance and exhaust emission of diesel engine in different ratios of lambda coefficient using diesel-ethanol fuel blends [Volume 60, Issue 60, 2020, Pages 19-28]
Moosavian, Seyed Ashkan Developing a virtual reality simulator for skill enhancement; case study: the assembly process of the EF7 national engine's timing belt [Volume 72, Issue 2, 2025, Pages 43-55]
Moqtaderi, Hamed Fuel consumption-aware powertrain selection and optimization for a B-class sedan [Volume 69, Issue 69, 2022, Pages 12-20]
Moqtaderi, Hamed Acoustic signal-based misfire detection in internal combustion engines using machine learning techniques [(Articles in Press)]
Moradi, F. Simulation of Subcooled Flow Boiling Occurring in Internal Combustion Engine Water Jacket by Numerical Modeling in a Channel with Hot Spot [Volume 53, Issue 53, 2019, Pages 23-32]
Moradi, Nima An experimental study of determining friction force between ring and cylinder by measuring piston movement [Volume 71, Issue 2, 2024, Pages 40-54]
Moradi kelardeh, Shahab An investigation on the effect of interference clearance of bushing on fatigue strength in triangle suspension [Volume 67, Issue 67, 2022, Pages 30-41]
Moradi Kelardeh, Sh. Effective of Main Bearing Bolt Manufacturing Parameters on Functional Performance in High Speed Diesel Engine using Torque-Angle Method [Volume 52, Issue 52, 2018, Pages 55-63]
Moradi Kelardeh, Shahab Investigation the effect of clamping stress on ultrasonic velocity in cylinder head bolt of diesel engine [Volume 50, Issue 50, 2018, Pages 29-40]
Morovatiyan, Mohammad Rasool Development of a 3D CFD model to analyze gas exchange process into intake manifold of an iVVT engine [Volume 36, Issue 36, 2014, Pages 51-60]
Mosavian, Seyed Ashkan Experimental and Analytical Investigation of the Oil Viscosity Effect on Vertical Vibrations of a CI Engine [Volume 46, Issue 46, 2017, Pages 65-74]
Moshiri, A. Experimental Study on the Effect of Hydrogen Addition to Compressed Natural Gas (CNG) on Engine Operation and Emission Reduction [Volume 15, Issue 15, 2009, Pages 29-35]
Moshki, Alireza The evaluation of plasma electrolytic oxidation properties on car compartments made with Mg alloy [Volume 69, Issue 69, 2022, Pages 49-60]
Moshrefi, A.H. Knock detection based on main vibration frequencies analysis in spark âignition turbocharged engine [Volume 34, Issue 34, 2014, Pages 17-27]
Moshrefi, Amirhossein Development of optimized model for filter and integrator of knock detection integrated circuit in automotive engine management system [Volume 37, Issue 37, 2015, Pages 65-74]
Motalebi, Sajad Investigating the effect of the coating process on improving the quality of mechanical bonding in the casting of aluminum cylinder block with cast-in iron liner [Volume 70, Issue 2, 2023, Pages 80-98]
Mousavi, Saeed Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Mousavi Seyedi, S.R. Experimental investigation of injector pump type effect on performance âparameters and emissions of âdiesel engine at full load [Volume 34, Issue 34, 2014, Pages 61-70]
Movahednejad, E. Study of fuel injection in a port injection engine with indirect injection with a special look at the impact on the performance of fuel injection timing and amount of pollutants [Volume 23, Issue 23, 2011, Pages 11-21]
Movahednejad, E. Using maximum entropy method for prediction of droplet size and velocity distribution in spray [Volume 25, Issue 25, 2012, Pages 35-44]
Mozafari, A.A. A New Approach for Inlet Diffuser of Automotive Catalytic Converter Considering Conversion Efficiency of Pollutants [Volume 18, Issue 18, 2010, Pages 42-50]
Mozafari, A.A. Thermodynamic Simulation of Spark Ignition Internal Combustion Engine Operation with Blends of Gasoline and CNG with Experimental Verification [Volume 23, Issue 23, 2011, Pages 32-44]
Mozaffari, A.A. Combustion Simulation of Natural Gas in Homogeneous Charge Compression Ignition (HCCI) Engines and Analysis of Effect of Engine Operating Conditions on Combustion Initiation [Volume 15, Issue 15, 2009, Pages 1-10]
Musavi Seyedi, Seyed Reza Functional Variables of a Biodiesel-Powered Single-Cylinder Diesel Engine: an Experimental Analysis [Volume 38, Issue 38, 2015, Pages 49-60]
N
Nabavi, R. An experimental study of pre-main injection strategy to optimize TDI diesel engine [Volume 41, Issue 41, 2016, Pages 55-62]
Nabavi, S. A. Principle of valves timing optimization in D87 diesel to premixed natural gas engine conversion [Volume 49, Issue 49, 2018, Pages 65-76]
Nabiei, Omid Study of the effect of nanoparticles on thermophysical properties and rheological behavior of cooling fluid in combustion engines [Volume 70, Issue 3, 2023, Pages 1-17]
Naderpour, A. Simulation of Fuel Consumption and Exhaust Emissions in Dual Fuel Samand Vehicle and Verification with NEDC Modal Test Results [Volume 15, Issue 15, 2009, Pages 11-16]
Naderpour, A. Driving Features and Their Influences on Hybrid Electric Vehicleâs Fuel Consumption and Exhaust Emissions [Volume 17, Issue 17, 2010, Pages 42-51]
Naderpour, A. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Nadjar Araabi, B. Recognition of Driving Style, Roadway Type, and Traffic Based on Information Available in Electronic Control unit of Vehicles in Real Traffic Conditions [Volume 17, Issue 17, 2010, Pages 52-59]
Najafi, B. Modeling of Effect of Biodiesel Cetane Number, Density and Viscosity on Ignition Delay [Volume 16, Issue 16, 2009, Pages 36-42]
Najafi, B. Experimental Investigation and Mathematical Modeling of Combustion Using Biodiesel from Restaurant Waste Cooking Oil [Volume 17, Issue 17, 2010, Pages 60-70]
Najafi, B. Numerical Simulation of Combustion Process of Biodiesel and Diesel Blending in a Compression Ignition Engine [Volume 19, Issue 19, 2010, Pages 19-28]
Najafi, Bahman CFD Simulation of the Biodiesel and Diesel Blends Combustion Process in an In-Direct Injection Diesel Engine [Volume 38, Issue 38, 2015, Pages 39-48]
Najafi, G. [Volume 16, Issue 16, 2009, Pages 29-35]
Najafi, G. Prediction Oil Parameter of Connecting Rod Small End Bearing of EF7 Engine by Using Artificial Neural Network by Simulation in AVL Excite Software [Volume 20, Issue 20, 2010, Pages 22-29]
Najafi, G. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Najafi, G.H. Modeling of an SI engine performance parameters and emissions using bio-ethanol-gasoline blends by genetic programming [Volume 27, Issue 27, 2012, Pages 47-57]
Najafi, G.H. Piston scuffing fault detection in an internal combustion engine using performance parameters and Fuzzy logic [Volume 31, Issue 31, 2013, Pages 11-20]
Najafi, Gholamhasan Investigation of Blended Palm Biodiesel-Diesel Fuel Properties with Water Emulsification [Volume 57, Issue 57, 2020, Pages 65-74]
Najafi, Gholamhassan Comparison of Aged and fresh Automotive Three-Way Catalyst in Driving Cycle [Volume 57, Issue 57, 2020, Pages 75-83]
Najafi, Gholamhassan Detection and classification of mechanical faults of an engine alternator based on vibration signals and frequency analysis [Volume 61, Issue 61, 2021, Pages 3-10]
Najafi, Gholamhassan Investigation of performance and exhaust emission of diesel engine in different ratios of lambda coefficient using diesel-ethanol fuel blends [Volume 60, Issue 60, 2020, Pages 19-28]
Najafi, M Development of a predictive Model for start of combustion of a reactivity-controlled compression ignition engine [Volume 62, Issue 62, 2021, Pages 3-13]
Najjari, B Emissions and fuel consumption reduction of the OM355 diesel engine using a common rail fuel injection and selective catalytic reduction systems [Volume 62, Issue 62, 2021, Pages 15-21]
Najjari, Behrooz Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Najjari, Behrouz Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Namar, Mohammad Mostafa Feasibility Study for Downsizing EF7 Engine, Numerical and Experimental Approach [Volume 61, Issue 61, 2021, Pages 73-85]
Namjoo, Moslem Evaluating the coupled thermo-mechanical stresses for an aluminum alloy piston used in a gasoline engine XU7 [Volume 42, Issue 42, 2016, Pages 33-42]
Namjoo, Moslem Numerical investigation on Effect of thermally isolated piston on improving SI engine performance during the cold start conditions [Volume 47, Issue 47, 2017, Pages 3-12]
Namvar Ayuri, A. Experimental study on the efficiency and pressure drop of three different engine types blow by oil separator [Volume 40, Issue 40, 2015, Pages 33-45]
Naseh, Arshia Simulation and performance analysis of a high-energy-density lithium–sulfur battery under cold start and standard european driving cycle conditions in an electric vehicle [Volume 72, Issue 3, 2025, Pages 24-42]
Nasiri, Sayyad The Effect of Injection Timing and Phasing on the Emission of a Gasoline Single Cylinder Engine [Volume 65, Issue 65, 2022, Pages 3-20]
Navabi, H. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Navabi, H. Root causes failure analysis of exhaust manifold heat shield failure [Volume 34, Issue 34, 2014, Pages 29-39]
Nayeri, Mohammad Jafar Enhancing the performance of a vapor compression refrigeration cycle by modifying the manufacturing process of the SLHX heat exchanger: transition from tangential to concentric configuration [Volume 72, Issue 2, 2025, Pages 19-30]
Nazaktabar, M. Simulation of Heat Transfer in the Cooling Passages of the âEF7â Engine Considering Boiling Phenomenon [Volume 19, Issue 19, 2010, Pages 64-73]
Nazari Chekoveri, M. Experimental investigation on the effect of injection pressure and injector installation angle on the penetration of the gasoline port fuel injector using high speed imaging method [Volume 52, Issue 52, 2018, Pages 29-42]
Nazari Chekoveri, Mahdi Accurate Simulation of Low-Pressure Port Fuel and Water Spray in Internal Combustion Engines; Numerical and Experimental Study [Volume 60, Issue 60, 2020, Pages 47-59]
Nazari Kian, Hadi Accurate Simulation of Low-Pressure Port Fuel and Water Spray in Internal Combustion Engines; Numerical and Experimental Study [Volume 60, Issue 60, 2020, Pages 47-59]
Nazemian, Mehran The effect of nozzle holes number with a focus on spray dynamics characteristics and its role in the performance and emissions of an RCCI engine [Volume 72, Issue 3, 2025, Pages 1-23]
Nazemian, Mehrdad The effect of nozzle holes number with a focus on spray dynamics characteristics and its role in the performance and emissions of an RCCI engine [Volume 72, Issue 3, 2025, Pages 1-23]
Nazer, A. Modeling of traffic conditions impact on fuel consumption and emissions of passenger cars in Arak city [Volume 35, Issue 35, 2014, Pages 53-61]
Nazoktabar, M. Using a single zone thermodynamic model in an HCCI engine to predict effective controlling parameters [Volume 25, Issue 25, 2012, Pages 13-23]
Nedayali, Amin Artificial neural network model to predict the performance of a diesel power generator fueled with biodiesel [Volume 42, Issue 42, 2016, Pages 43-50]
Nejat, M. Port Development of a Port Injection Turbocharged Engine to Improve Combustion Quality & Performance Parameters [Volume 49, Issue 49, 2018, Pages 47-66]
Nejat, Mohammad Turbocharger bearing housing temperature measurement at different engine operating conditions [Volume 71, Issue 2, 2024, Pages 30-39]
Nekoufar, K. Study of fuel injection in a port injection engine with indirect injection with a special look at the impact on the performance of fuel injection timing and amount of pollutants [Volume 23, Issue 23, 2011, Pages 11-21]
Nekoufar, K. Using maximum entropy method for prediction of droplet size and velocity distribution in spray [Volume 25, Issue 25, 2012, Pages 35-44]
Nemati, Alireza The Effect of Injection Timing and Phasing on the Emission of a Gasoline Single Cylinder Engine [Volume 65, Issue 65, 2022, Pages 3-20]
Neshan, M.A. Integration of exhaust manifold with engine cylinder head towards size and weight reduction [Volume 30, Issue 30, 2013, Pages 55-65]
Neshat, E Comprehensive Investigation on the Effect of the EGR Components on n-heptane HCCI Combustion [Volume 63, Issue 63, 2021, Pages 49-60]
Neshat Esfahlani, E. A comparative study of effect of valve overlap on HCCI engines [Volume 32, Issue 32, 2013, Pages 3-12]
Neshat Esfahlani, E. Modeling of HCCI combustion and emissions using a multi-zone model [Volume 33, Issue 33, 2014, Pages 13-21]
Neshat Esfahlani, E. Investigation on the effect of reformer gas addition on HCCI combustion of blended fuel [Volume 40, Issue 40, 2015, Pages 23-33]
Neyestani, J. Experimental Prediction of Nusselt Number and Coolant Heat Transfer Coefficient in Compact Heat Exchanger Performed with Ñ-NTU Method [Volume 18, Issue 18, 2010, Pages 62-70]
Niazmand, H. Numerical Analysis of Injected EGR/Blowby Gases Distribution in Intake Manifold [Volume 15, Issue 15, 2009, Pages 55-65]
Nik'khah, Mahdi Design of Intelligent Cooling System with electrical Thermostat and Implementation of Strategy in Engine Control Unit [Volume 43, Issue 43, 2016, Pages 55-62]
Nikravan, M. An Investigation of High Cycle Fatigue Behavior of Magnesium Alloy for Cylinder Head Application [Volume 24, Issue 24, 2011, Pages 29-35]
Nikroo, Naiemeh Numerical investigation on improvement of cooling system based on heat pipe for LCO battery by using NTGK model [Volume 71, Issue 2, 2024, Pages 69-90]
Nikzad, Leyla The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
Nikzadfar, Kamyar Development of an in-cylinder processes model of a CVVT gasoline engine using artificial neural network [Volume 51, Issue 51, 2018, Pages 53-62]
Nikzadfar, Kamyar Feasibility Study for Downsizing EF7 Engine, Numerical and Experimental Approach [Volume 61, Issue 61, 2021, Pages 73-85]
N. Kian, H. Study of two-stage turbocharging for compensation of low-end torque [Volume 49, Issue 49, 2018, Pages 39-46]
Noori, H. Effect of starting temperature and belt width on lateral force of timing belt [Volume 48, Issue 48, 2017, Pages 13-18]
Noori, R. A study of factors affecting plastics intake manifold strength against backfire phenomena [Volume 48, Issue 48, 2017, Pages 49-57]
Norouzi Ghazbi, S. Study on effect of electric/combustion engine on performance of a parallel hybrid vehicle and proposing engine selection algorithm [Volume 31, Issue 31, 2013, Pages 21-31]
Nosrat, G. Evaluation of continuum damage at different temperatures for aluminum-silicon alloy of engine piston within low-cycle fatigue regime [Volume 52, Issue 52, 2018, Pages 43-54]
Nouripour, Mohammadhossain The evaluation of plasma electrolytic oxidation properties on car compartments made with Mg alloy [Volume 69, Issue 69, 2022, Pages 49-60]
Nourpour, A.R. Analysis of Contact Stresses and MLS Cylinder Head Gasket Behavior Using Finite Element Method [Volume 15, Issue 15, 2009, Pages 45-54]
Nowruzi, H. Numerical study of effect of ambient backpressure and temperature on spray characteristics of heavy fuel oil/n-butanol blend [Volume 31, Issue 31, 2013, Pages 43-53]
Nowruzi, H. Numerical investigation of non-reacting spray characteristics of heavy âfuel and alternative fuel under high injection pressure [Volume 34, Issue 34, 2014, Pages 3-15]
Nowruzi, Hashem A Numerical Study on Non-Reacting Spray Characteristics of Different Marine Diesel Fuel-Water Emulsion Blends [Volume 44, Issue 44, 2016, Pages 65-77]
N. Shirvan, H. Energy balance on a three-cylinder engine with turbocharger [Volume 49, Issue 49, 2018, Pages 29-38]
O
Ohadi Hamedani, A.R. Vibration control of an automotive engine using active mounts [Volume 30, Issue 30, 2013, Pages 3-14]
Ohadi Hamedani, A.R. Dynamic modeling of national engine on mounts together with experimental validation [Volume 33, Issue 33, 2014, Pages 31-41]
Ommi, F. Experimental Study on the Effect of Hydrogen Addition to Compressed Natural Gas (CNG) on Engine Operation and Emission Reduction [Volume 15, Issue 15, 2009, Pages 29-35]
Ommi, F. Experimental Investigation of the Combustion of a Spark Ignition Engine, With Gasoline-Ethanol-MTBE Blends as Fuel, to Reduce Fuel Consumption and pollutants [Volume 16, Issue 16, 2009, Pages 22-28]
Ommi, F. Investigation of Effects of Spark Plugâs Electrodes Erosion on the Required Ignition Voltage and Performance of Natural Gas Engine [Volume 21, Issue 21, 2011, Pages 21-34]
Ommi, F. Study of fuel injection in a port injection engine with indirect injection with a special look at the impact on the performance of fuel injection timing and amount of pollutants [Volume 23, Issue 23, 2011, Pages 11-21]
Ommi, F. Performance Evaluation of a Samand Vehicle with Internal Combustion Engine System and Hybrid Electric-Fuel Cell System [Volume 24, Issue 24, 2011, Pages 51-64]
Ommi, F. Using maximum entropy method for prediction of droplet size and velocity distribution in spray [Volume 25, Issue 25, 2012, Pages 35-44]
Ommi, F. Effect of electrode erosion on the required ignition voltage of spark plug in CNG spark ignition engine [Volume 26, Issue 26, 2012, Pages 31-39]
Ommi, F. Modeling of an SI engine performance parameters and emissions using bio-ethanol-gasoline blends by genetic programming [Volume 27, Issue 27, 2012, Pages 47-57]
Ommi, Fathollah Design and simulation of a hybrid electric vehicle in order to increasing efficiency and reducing pollution [Volume 37, Issue 37, 2015, Pages 35-48]
Omrani, R. An Investigation on the Effects of Friction and Heat Transfer on Flow within the Inlet Manifold of an Internal Combustion Engine by Finite- Volume Method [Volume 20, Issue 20, 2010, Pages 59-68]
Ostad Shabani, Mohsen The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
P
Padash, A. Simulation of piston and ring friction at the motoring condition and investigation effect of combustion and clearance between the piston and cylinder [Volume 39, Issue 39, 2015, Pages 41-48]
Padash, Asghar A model for estimation of wear of engine rings based on the amount of blowby and oil consumption in durability tests [Volume 71, Issue 1, 2024, Pages 67-78]
Parivar, A. H. Energy balance on a three-cylinder engine with turbocharger [Volume 49, Issue 49, 2018, Pages 29-38]
Parivar, A. H. Port Development of a Port Injection Turbocharged Engine to Improve Combustion Quality & Performance Parameters [Volume 49, Issue 49, 2018, Pages 47-66]
Parivar, A.H. Effect of Ambient Conditions and Fuel Composition on Fuel Consumption and NOx Emission Measurement for Vehicle in Driving Cycle [Volume 21, Issue 21, 2011, Pages 13-20]
Parivar, A.H. Using predictive combustion model in combustion modeling of cooled EGR turbocharged engine [Volume 25, Issue 25, 2012, Pages 57-67]
Parivar, A.H. Knock detection based on main vibration frequencies analysis in spark âignition turbocharged engine [Volume 34, Issue 34, 2014, Pages 17-27]
Parivar, amirhossein Machine Learning-Driven Modeling of Variable Valve Timing Effect on Fuel Consumption and Emission Reduction in a Turbocharged Port-Injection Engine [(Articles in Press)]
Parivar, Amirhossein Conceptual and experimental study of an Atkinson cycle engine of a Series-Parallel hybrid electric vehicle [Volume 70, Issue 4, 2024, Pages 69-80]
Parivar, Amir Hossein Role of passenger cars and taxies in air pollution of Tehran, Iran [Volume 69, Issue 69, 2022, Pages 21-29]
Parivar, Amir Hossein Study of GDI injector in constant volume chamber by optical measurements and CFD-Simulation [Volume 69, Issue 69, 2022, Pages 39-48]
Parivar, AmirHossein CFD simulation of wall film during fuel injection and combustion in a three-cylinder turbocharged gasoline direct injection engine [Volume 70, Issue 4, 2024, Pages 1-13]
Parsa, S Emissions and fuel consumption reduction of the OM355 diesel engine using a common rail fuel injection and selective catalytic reduction systems [Volume 62, Issue 62, 2021, Pages 15-21]
Parsa, Somaye Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Partovi, B. Effects of piston bowl geometry on combustion and emissions characteristics of a natural gas/diesel RCCI engine [Volume 40, Issue 40, 2015, Pages 59-70]
Parvaz, Hadi An investigation on the effect of interference clearance of bushing on fatigue strength in triangle suspension [Volume 67, Issue 67, 2022, Pages 30-41]
Pashaei, J. Determination of PM and NOx Pollutants Correction Factors in IC Diesel Engines Related to sea level Condition [Volume 21, Issue 21, 2011, Pages 48-57]
Pashaei, Jafar Development of a zero-dimensional turbulence model for the flow field of spark-ignition engines, considering vortex motions, based on a new approach [Volume 71, Issue 4, 2025, Pages 77-101]
Patil, A. Experimental Study of Hydrogen Addition Impact on Emissions and Performance of a Natural Gas Fueled Engine [Volume 14, Issue 14, 2009, Pages 43-50]
Paykani, A. Effects of piston bowl geometry on combustion and emissions characteristics of a natural gas/diesel RCCI engine [Volume 40, Issue 40, 2015, Pages 59-70]
Pirkandi, J Thermodynamic Analysis of a Turboprop Engine Equipped With Solid Oxide Fuel Cell [Volume 62, Issue 62, 2021, Pages 55-63]
Pirouzpanah, S.V. Theoretical Investigation of Combustion Process in Dual Fuel Engines at Part Load Considering the Effect of Exhaust Gas Recirculation [Volume 14, Issue 14, 2009, Pages 51-62]
Pirzadeh, Y. Formation of diesel-water nano-emulsion: Importance, advantages and evaluation of engine performance [Volume 33, Issue 33, 2014, Pages 53-60]
Pishgooie, M. The Effect of Using Variable Valve System on XU7/L3 Engine [Volume 21, Issue 21, 2011, Pages 58-72]
Poorghasemi, Kamran Study on the effect of using reformed biogas as a low reactivity fuel in a dual-fuel engine (RCCI) [Volume 59, Issue 59, 2020, Pages 73-93]
Poorvousooghi Gargari, Hassan Performance and Emissions of a Tractor engine operating on biodiesel-diesel blends with EGR [Volume 42, Issue 42, 2016, Pages 13-22]
Poorvousooghi Gargari, Hassan Evaluate the effect of biodiesel and EGR system on diesel engine emissions [Volume 42, Issue 42, 2016, Pages 23-32]
Porgoo, Mohammad Ali Powertrain mounting system optimization to improve vibration behavior for EF7 engine [Volume 53, Issue 53, 2019, Pages 55-68]
Pourbafarani, Z. Simulation of the Double Sided Clutch AMT and Investigation of Itâs Effect on HEV Performance [Volume 21, Issue 21, 2011, Pages 3-12]
Pourfalah, M. An experimental study of pre-main injection strategy to optimize TDI diesel engine [Volume 41, Issue 41, 2016, Pages 55-62]
Pourfallah, M. The Effect of Different Injection Configuration on Combustion and Emissions Formation in a Heavy Duty Diesel Engine [Volume 16, Issue 16, 2009, Pages 43-51]
Pourfallah, M. Investigation of combustion chamber thermal stratification effect on combustion performance of homogeneous charge compression ignition engine [Volume 35, Issue 35, 2014, Pages 3-16]
Pourfallah, Mohsen Operating Range Expansion in a HCCI Natural Gas Engine Using Charge and Thermal Stratification in Combustion Chamber [Volume 54, Issue 54, 2019, Pages 51-63]
Pourhamid, R. Thermal analysis of functionally graded materials in cylinders and pistons based on super element method [Volume 30, Issue 30, 2013, Pages 25-36]
Poursabbagh, Hosein Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Pourtaghi Yousefdeh, Sadegh Experimental Investigation of the Combination of Ethanol-Biodiesel, Ethanol-Diesel, and Ethanol-Biodiesel-Diesel Emulsion Blends on Performance and Emissions of Direct Injection Diesel Engines [Volume 66, Issue 66, 2022, Pages 3-21]
Q
Qasemi, E. Oil Quality Monitoring in Gasoline Spark Ignition Engine Using Oil Dielectric Measurement [Volume 53, Issue 53, 2019, Pages 45-54]
Qasemian, A. Simulation of Subcooled Flow Boiling Occurring in Internal Combustion Engine Water Jacket by Numerical Modeling in a Channel with Hot Spot [Volume 53, Issue 53, 2019, Pages 23-32]
Qasemian, Ali Accurate Simulation of Low-Pressure Port Fuel and Water Spray in Internal Combustion Engines; Numerical and Experimental Study [Volume 60, Issue 60, 2020, Pages 47-59]
Qasemian, Ali Utilization of Stirling engine to improve the performance and fuel consumption of an internal combustion engine by exhaust gas heat recovery [Volume 66, Issue 66, 2022, Pages 68-84]
Qasemian, Ali Numerical investigation on improvement of cooling system based on heat pipe for LCO battery by using NTGK model [Volume 71, Issue 2, 2024, Pages 69-90]
Qasemian, Ali The effect of using copper nanoparticles in engine oil on fuel consumption [Volume 71, Issue 1, 2024, Pages 52-66]
Qasemian, Ali Investigation of the viscosity of CuO–ZnO hybrid nanolubricant for application in internal combustion engines with a MD approach [Volume 72, Issue 3, 2025, Pages 64-84]
Qasemian, Ali Simulation of the Effect of Using a Turbocharger on XU7 Engine Performance with Mechanical and Electronic Wastegate Control Mechanisms [(Articles in Press)]
R
Rabbani, Yousef Concept selection for engine components using the DEMATEL-ANP-TOPSIS combination method: case study for cam bearing frame part [Volume 61, Issue 61, 2021, Pages 61-71]
Rabeti, Masoud Evaluation of the Effects of Equivalence Ratio on the Combustion in an HCCI Engine [Volume 61, Issue 61, 2021, Pages 47-59]
Rabiei, M. The Effect of Valve Lift on In-Cylinder Flow, Performance and Emissions in a Turbocharged DI Diesel Engine [Volume 18, Issue 18, 2010, Pages 3-11]
Raei Tabar, Abbas Investigation of Three-Way Catalytic Converters of a 1.7L Turbocharged Bi-Fuel Engine Using CNG and Gasoline Fuels [Volume 44, Issue 44, 2016, Pages 53-64]
Rafiei, Ashkan Numerical analysis of the effect of new matrix network structure technology to enhancement the internal heat transfer of gas turbine blades [Volume 71, Issue 3, 2024, Pages 56-76]
Rafiei, S. Optimization of performance in tractor engine with biodiesel-ethanol-diesel fuels using response surface methodology [Volume 29, Issue 29, 2013, Pages 15-24]
Rahbari Asiabi, Hadi Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Rahbari Asiabi, Hadi Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Rahi, Abbas Experimental and Analytical Investigation of the Oil Viscosity Effect on Vertical Vibrations of a CI Engine [Volume 46, Issue 46, 2017, Pages 65-74]
Rahimi, Nima Simulation of the Effect of Using a Turbocharger on XU7 Engine Performance with Mechanical and Electronic Wastegate Control Mechanisms [(Articles in Press)]
Rahimi Asiabaraki, Hossein The Effect of Injection Timing and Phasing on the Emission of a Gasoline Single Cylinder Engine [Volume 65, Issue 65, 2022, Pages 3-20]
Rahimi Asiabaraki, Hossein Investigation of the effect of AL2O3 nanofluid in M13NI engine cooling system [Volume 70, Issue 1, 2023, Pages 47-65]
Rahimi Asiabaraki, Hossein Experimental analysis of the effect of using aluminum oxide nanofluid in improving the heat transfer of XU7 engine radiator [Volume 70, Issue 2, 2023, Pages 66-79]
Rahimi Asiabaraki, Hossein Simulation of cylinder deactivation and its effects on emission and fuel consumption [Volume 71, Issue 1, 2024, Pages 79-90]
Rahimi Asiabaraki, Hossein Static analysis, fatigue and buckling of connecting rod by finite element method [Volume 71, Issue 3, 2024, Pages 32-44]
Rahimi Asiabaraki, Hossein Reduction of fuel consumption and emissions of Iranian naturally aspirated engine on Samand vehicle with thermal management [Volume 71, Issue 4, 2025, Pages 58-76]
Rahimi Asiabaraki, Hossein Developing a virtual reality simulator for skill enhancement; case study: the assembly process of the EF7 national engine's timing belt [Volume 72, Issue 2, 2025, Pages 43-55]
Rahimi Asiabaraki, Hossein Evaluation of changes in diesel fuel type on the injection rate of diesel common rail injectors [Volume 72, Issue 3, 2025, Pages 43-63]
Rahimi Asiabaraki, Hossein Simulation of the Effect of Using a Turbocharger on XU7 Engine Performance with Mechanical and Electronic Wastegate Control Mechanisms [(Articles in Press)]
Rahimipour, Mohammad Reza The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
Rahmani, Mohammad Reza Defect detection in piston rings using deep learning-based computer vision [Volume 72, Issue 2, 2025, Pages 9-18]
Rahmati, Edres Experimental study of the effect of magnetic flux density on fuel consumption and emissions in diesel engine [Volume 66, Issue 66, 2022, Pages 57-67]
Rahmatinejad, Bahman Investigation of the effect of AL2O3 nanofluid in M13NI engine cooling system [Volume 70, Issue 1, 2023, Pages 47-65]
Rahmatinejad, Bahman Experimental analysis of the effect of using aluminum oxide nanofluid in improving the heat transfer of XU7 engine radiator [Volume 70, Issue 2, 2023, Pages 66-79]
Rahmatinejad, Bahman Static analysis, fatigue and buckling of connecting rod by finite element method [Volume 71, Issue 3, 2024, Pages 32-44]
Rajabi, Mohammad Ali Role of passenger cars and taxies in air pollution of Tehran, Iran [Volume 69, Issue 69, 2022, Pages 21-29]
Rajaei Salmasi, F. Recognition of Driving Style, Roadway Type, and Traffic Based on Information Available in Electronic Control unit of Vehicles in Real Traffic Conditions [Volume 17, Issue 17, 2010, Pages 52-59]
Rakhshan, Rezvan Simulation and scale-up of a centrifugal compressor for a turbocharger of a lean combustion engine employing 1-D and 3-D design and geometrical modification of the impeller [Volume 66, Issue 66, 2022, Pages 22-35]
Ramezani, A. Analytical and Experimental Modal Analysis of Crankshaft, Flywheel and Pulley Set [Volume 24, Issue 24, 2011, Pages 13-20]
Ranieri, Stefano Direct injection of methane in advanced propulsion systems: effects of thermodynamic conditions [Volume 69, Issue 69, 2022, Pages 30-38]
Ranjbar, A.A. Investigation of combustion chamber thermal stratification effect on combustion performance of homogeneous charge compression ignition engine [Volume 35, Issue 35, 2014, Pages 3-16]
Ranjbar, Ali Akbar Evaluation of the Effects of Equivalence Ratio on the Combustion in an HCCI Engine [Volume 61, Issue 61, 2021, Pages 47-59]
Ranjbar, Alireza Defect detection in piston rings using deep learning-based computer vision [Volume 72, Issue 2, 2025, Pages 9-18]
Raoofy, A. Vibration control of an automotive engine using active mounts [Volume 30, Issue 30, 2013, Pages 3-14]
Rashidi, A.M. Effects of Nano-Particles on Properties of Engine Oil and its Functionality Rate on Wear Reduction [Volume 24, Issue 24, 2011, Pages 3-12]
Rastegar, Nima Analyzing driving behavior for fuel efficiency using ECU data based on artificial intelligence [Volume 71, Issue 1, 2024, Pages 1-15]
Razavi, Mansour The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
Razavi, S.E. The Effect of Valve Lift on In-Cylinder Flow, Performance and Emissions in a Turbocharged DI Diesel Engine [Volume 18, Issue 18, 2010, Pages 3-11]
Razavi, S.E. An Investigation on the Effects of Friction and Heat Transfer on Flow within the Inlet Manifold of an Internal Combustion Engine by Finite- Volume Method [Volume 20, Issue 20, 2010, Pages 59-68]
Razavi, S.E. Enhancement of a Diesel Engine Inlet Port for Pollutant Reduction and Performance Optimization [Volume 22, Issue 22, 2011, Pages 39-49]
Razmavar, Alireza Investigation of particulate fouling in exhaust gas recirculation coolers in diesel engines [Volume 37, Issue 37, 2015, Pages 49-64]
Reyhanian, M. Controlling natural gas combustion timing in HCCI engine with synthetic gas enrichment using a chemical kinetic model [Volume 32, Issue 32, 2013, Pages 13-20]
Reyhanian, M. Experimental investigation of gasoline fueled HCCI engine load expansion [Volume 39, Issue 39, 2015, Pages 3-10]
Rezaee, M. Introducing an Approach for Feasibility Study of Replacing the Manual Transmission System with CVT System to Reduce the Fuel Consumption [Volume 16, Issue 16, 2009, Pages 52-61]
Rezaee, M. Development of a Dynamic Model and Optimal Control of CVT Transmission System for Minimum Fuel Consumption [Volume 21, Issue 21, 2011, Pages 35-47]
Rezaei, M. Experimental and finite element vibrational analysis of exhaust manifold heat shield [Volume 26, Issue 26, 2012, Pages 41-48]
Rezaei, M. Experimental and numerical investigation of stress in engine crankshaft [Volume 32, Issue 32, 2013, Pages 29-36]
Rezaei, M. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Rezaei, M. Root causes failure analysis of exhaust manifold heat shield failure [Volume 34, Issue 34, 2014, Pages 29-39]
Rezaei, M. [Volume 39, Issue 39, 2015, Pages 33-39]
Rezaei, M. Thermal analysis of multiple layers steel(MLS) cylinder head gasket via test [Volume 48, Issue 48, 2017, Pages 19-26]
Rezaeian, Bagher Design and analysis of a thermoelectric generator for a heavy-duty vehicle in âreal road test [Volume 68, Issue 68, 2022, Pages 12-22]
Rezvani Rad, M. Coating thickness effect on stress distribution of coated cylinder head considering residual stress [Volume 26, Issue 26, 2012, Pages 49-57]
Riazi, S. M. Design of Nondestructive System for Hardness of Carbonitrided Steel Parts âUsing Eddy Current Testing Method: Case study on the Tappet Parts [Volume 52, Issue 52, 2018, Pages 19-28]
Riyahi Chaleshtari, homayoun Comparison between revolution sensor by using PVDF sensor in XU7 engine and vibration energy harvesting [Volume 44, Issue 44, 2016, Pages 3-18]
Rohani, Abbas Evaluation of reliability of diesel engine crankshaft by accelerated test method [Volume 72, Issue 2, 2025, Pages 56-71]
Rohani, R. Failure analysis of a dynamometer drive shaft coupled to an engine [Volume 30, Issue 30, 2013, Pages 37-46]
Rohani, R. Study of ball bearings failure modes in an eddy current dynamometer [Volume 41, Issue 41, 2016, Pages 3-11]
Rohani Bastami, Abbas Simulation of torsional vibrations of dual mass flywheel in a 3-cylinder engine [Volume 70, Issue 1, 2023, Pages 1-13]
Roozban, M. Failure analysis of an intake valve in a gasoline engine [Volume 26, Issue 26, 2012, Pages 3-9]
Roozban, M. Failure analysis of a dynamometer drive shaft coupled to an engine [Volume 30, Issue 30, 2013, Pages 37-46]
Roozban, M. Complete analysis for material, mechanism, vibration, stress and fatigue in valve spring [Volume 33, Issue 33, 2014, Pages 3-12]
Roozban, M. Root causes failure analysis of exhaust manifold heat shield failure [Volume 34, Issue 34, 2014, Pages 29-39]
Roozban, M. [Volume 39, Issue 39, 2015, Pages 33-39]
Roozban, M. Study of ball bearings failure modes in an eddy current dynamometer [Volume 41, Issue 41, 2016, Pages 3-11]
Rostami, Elyas Design and simulation of a hybrid electric vehicle in order to increasing efficiency and reducing pollution [Volume 37, Issue 37, 2015, Pages 35-48]
Rostami, S. Experimental Investigation of Effect of Injection Pressure on Performance of a Diesel Engine Using Blends of Biodiesel and Diesel [Volume 21, Issue 21, 2011, Pages 73-82]
Rostami, Sajjad The Effect of throttle valve positions on thermomechanical exergy, burned fuel exergy, exergy with heat transfer and exergy with work transfer of an SI Engine [Volume 43, Issue 43, 2016, Pages 31-40]
S
Saadati, Mansour Simulation and investigation of the effect of oil flow rate, electric signal of flow control valve and controller on the performance of a wet clutch [Volume 54, Issue 54, 2019, Pages 65-77]
Saberinejad, Hojjat Analysis of the effect of placement of radiator and condenser fans in a sample vehicle on the cooling system [Volume 72, Issue 1, 2025, Pages 35-44]
Saboohi, Zoheir Conceptual design of a conventional aero gas turbine combustor for soot and gaseous emissions reduction [Volume 72, Issue 1, 2025, Pages 1-14]
Saeedpour, Mohammadreza The effect of using copper nanoparticles in engine oil on fuel consumption [Volume 71, Issue 1, 2024, Pages 52-66]
Saeidi Googarchin, Hamed Clustering and smoothing using real data collected from city buses to extract the driving cycle in Kermanshah city [Volume 71, Issue 2, 2024, Pages 1-17]
Safari, Hossein The evaluation of plasma electrolytic oxidation properties on car compartments made with Mg alloy [Volume 69, Issue 69, 2022, Pages 49-60]
Safari, Saeed The evaluation of plasma electrolytic oxidation properties on car compartments made with Mg alloy [Volume 69, Issue 69, 2022, Pages 49-60]
Safarpour, Pedram Simulation of torsional vibrations of dual mass flywheel in a 3-cylinder engine [Volume 70, Issue 1, 2023, Pages 1-13]
Safieddin Ardebili, Seyed Mohammad Evaluation of the Effects of Equivalence Ratio on the Combustion in an HCCI Engine [Volume 61, Issue 61, 2021, Pages 47-59]
Saidi, M.H. Experimental Prediction of Nusselt Number and Coolant Heat Transfer Coefficient in Compact Heat Exchanger Performed with Ñ-NTU Method [Volume 18, Issue 18, 2010, Pages 62-70]
Sajedi, P. Modeling of traffic conditions impact on fuel consumption and emissions of passenger cars in Arak city [Volume 35, Issue 35, 2014, Pages 53-61]
Sakhaei, B. Analytical and Experimental Modal Analysis of Crankshaft, Flywheel and Pulley Set [Volume 24, Issue 24, 2011, Pages 13-20]
Sakhaei, B. Fault diagnosis in engine spark plug by vibration analysis using neural network [Volume 28, Issue 28, 2012, Pages 21-29]
Sakhaei, B. Mathematical simulation of a vehicle radiator by genetic algorithm method and comparison with experimental data [Volume 30, Issue 30, 2013, Pages 15-23]
Sakhaei, M. Failure Analysis of a Four Cylinder Diesel Engine Crankshaft Made From Nodular Cast Iron [Volume 22, Issue 22, 2011, Pages 21-28]
Salamat, Mohammad Kasra Agricultural tractor driving cycle extraction using artificial intelligence [Volume 70, Issue 4, 2024, Pages 14-26]
Salarian, Hesamoddin The Effect of Hydrogen Addition on a RCCI Engine Performance Fueled with Natural GasDiesel Fuel at Low Load Range [Volume 65, Issue 65, 2022, Pages 60-74]
Salavati-Zadeh, A. The effect of ethanol combustion on HCCI engine performance and emissions [Volume 41, Issue 41, 2016, Pages 21-30]
Salehi, Fahime Acoustic signal-based misfire detection in internal combustion engines using machine learning techniques [(Articles in Press)]
Salehi, Meysam Fuel consumption optimization of a series hybrid electric vehicle utilizing fuzzy logic control [Volume 68, Issue 68, 2022, Pages 23-30]
Salehi, R. Nonlinear Oxygen Sensor Output Voltage Estimation in a Gasoline Engine Using NARX Model [Volume 22, Issue 22, 2011, Pages 13-20]
Salehi, R. Steady-state modeling of a turbocharger in gasoline engines [Volume 26, Issue 26, 2012, Pages 21-30]
Salek, F Numerical investigation of the impacts of ammonia injection on the performance of EF7 engine with CNG fuel [Volume 62, Issue 62, 2021, Pages 23-29]
Salimian, Mohammadhosein Investigation on the effect of using electric supercharging on the performance of a SI-TC engine [Volume 43, Issue 43, 2016, Pages 41-54]
Salimifar, Saeed Improvement of hardness and tribology properties of engine parts by formation of surface composite layer containing alumina particles by using gas-tungsten arc welding process [Volume 43, Issue 43, 2016, Pages 3-12]
Samaras, Z. Reducing CO2 Emissions from Road Transport - Overview of the Main Initiatives and Technical Measures Proposed to Date in Europe [Volume 18, Issue 18, 2010, Pages 32-41]
Samimi Abianeh, O. Investigation of Swirling and Tumbling Flow Pattern of Spark Ignition Engine [Volume 14, Issue 14, 2009, Pages 27-34]
Sapee, Syazwan Investigation of Blended Palm Biodiesel-Diesel Fuel Properties with Water Emulsification [Volume 57, Issue 57, 2020, Pages 65-74]
Sarabi, M The Effect Of Burned Residual Gases On Gasoline-NG Dual-Fuel Engine Combustion Performance With Skip-Fire Technique [Volume 63, Issue 63, 2021, Pages 3-11]
Sarabi, M. Experimental study of a spark ignition single-cylinder research engine exhaust emissions in gasoline and natural gas fuel cases [Volume 39, Issue 39, 2015, Pages 49-55]
Sarabi, Mehrdad Simulating and Validating a multi-zone thermodynamic-model for gasoline-NG dual-fuel SI engines and predicting NO emission [Volume 67, Issue 67, 2022, Pages 3-15]
Saraei, Hamidreza Development of balance shaft and flywheel for single cylinder diesel engine based on analytical approach and comparison with the simulation result [Volume 51, Issue 51, 2018, Pages 63-74]
Saravani, Saeid Simulation of fuel consumption of a hydrogen fuel cell electric vehicle with a thermostat control strategy and variables affecting its fuel consumption in ADVISOR software [Volume 72, Issue 3, 2025, Pages 85-105]
Sarlak, Nosratollah Experimental study of the effect of magnetic flux density on fuel consumption and emissions in diesel engine [Volume 66, Issue 66, 2022, Pages 57-67]
Sattarifar, I. Study of Effects of Combustion Gases and Cooling Thermal Boundary Conditions on Temperature Distribution of a Heavy Duty Diesel Engine Cylinder Head [Volume 17, Issue 17, 2010, Pages 71-81]
Savadkohi, L. Study on Effect of Change in Behavior of 457-LA Diesel Engine Cooling System on Its Performance [Volume 16, Issue 16, 2009, Pages 16-21]
Savadkouhi, L. Experimental Investigation of Effect of Injection Pressure on Performance of a Diesel Engine Using Blends of Biodiesel and Diesel [Volume 21, Issue 21, 2011, Pages 73-82]
Sedighi, Reza Numerical study on the effect of geometry on pressure caused by the injectors sealing on the mechanical behavior of common rail fuel of Shahin car at the engine operating temperature conditions [Volume 71, Issue 3, 2024, Pages 1-15]
Sepehrian, Hanye Role of passenger cars and taxies in air pollution of Tehran, Iran [Volume 69, Issue 69, 2022, Pages 21-29]
Seyed Razavi, S.E. Determination of PM and NOx Pollutants Correction Factors in IC Diesel Engines Related to sea level Condition [Volume 21, Issue 21, 2011, Pages 48-57]
Shabani, Z. Optimization of performance in tractor engine with biodiesel-ethanol-diesel fuels using response surface methodology [Volume 29, Issue 29, 2013, Pages 15-24]
Shadidi, Behdad Investigation of performance and exhaust emission of diesel engine in different ratios of lambda coefficient using diesel-ethanol fuel blends [Volume 60, Issue 60, 2020, Pages 19-28]
Shafaghat, Rouzbeh Feasibility Study for Downsizing EF7 Engine, Numerical and Experimental Approach [Volume 61, Issue 61, 2021, Pages 73-85]
Shafaghat, Rouzbeh Experimental investigation of injection timing effect on RCCI Engine using waste oil biodiesel as high reactive fuel [Volume 71, Issue 4, 2025, Pages 44-57]
Shafee, S. Three-Dimensional Modeling of Combustion Process, Soot and NOx formation In a Direct-injection Diesel Engine [Volume 14, Issue 14, 2009, Pages 35-42]
Shafiei, B. Numerical simulation of in-cylinder tumble flow field measurements and comparison to experimental results [Volume 26, Issue 26, 2012, Pages 11-19]
Shafiei Fini, Ali Impact of pressure on thermal efficiency of phase change material-based BTMS for electric powertrain [Volume 71, Issue 3, 2024, Pages 16-31]
Shafiei Sabet, A. Investigation of Swirling and Tumbling Flow Pattern of Spark Ignition Engine [Volume 14, Issue 14, 2009, Pages 27-34]
Shafiei Sabet, A. Experimental Study on the Effect of Hydrogen Addition to Compressed Natural Gas (CNG) on Engine Operation and Emission Reduction [Volume 15, Issue 15, 2009, Pages 29-35]
Shafiei Sabet, A. Experimental Investigation of the Combustion of a Spark Ignition Engine, With Gasoline-Ethanol-MTBE Blends as Fuel, to Reduce Fuel Consumption and pollutants [Volume 16, Issue 16, 2009, Pages 22-28]
Shahabiniya, Mohammad Parsa Investigation of the Effect of Normal Butanol–Gasoline Blends on the Performance of the Iranian National Engine [(Articles in Press)]
Shahangian, S.N. Effect of Initial Temperature and EGR on Combustion and Performance Characteristics of Homogenous Charge Compression Ignition Engine Fueled with Dimethyl Ether [Volume 14, Issue 14, 2009, Pages 63-70]
Shahangian, S.N. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Shahbakhti, M. Using a single zone thermodynamic model in an HCCI engine to predict effective controlling parameters [Volume 25, Issue 25, 2012, Pages 13-23]
Shahbazian, Hamidreza Numerical analysis of the effect of new matrix network structure technology to enhancement the internal heat transfer of gas turbine blades [Volume 71, Issue 3, 2024, Pages 56-76]
Shahriari, Bherouz Numerical and experimental analysis of lateral vibration of a turbocharger rotor in rotating and non-rotating conditions [Volume 70, Issue 1, 2023, Pages 14-27]
Shakarami, I Experimental study of the use of oxygenated Ethanol and Diisopropyl ethercomponeds in gasoline fuel and their effects ontheXU7JP/L3 engine performance and emissions [Volume 63, Issue 63, 2021, Pages 13-21]
Shakeri, A. Simulation of Subcooled Flow Boiling Occurring in Internal Combustion Engine Water Jacket by Numerical Modeling in a Channel with Hot Spot [Volume 53, Issue 53, 2019, Pages 23-32]
Shalchian, M. Knock detection based on main vibration frequencies analysis in spark âignition turbocharged engine [Volume 34, Issue 34, 2014, Pages 17-27]
Shalchian, Majid Development of optimized model for filter and integrator of knock detection integrated circuit in automotive engine management system [Volume 37, Issue 37, 2015, Pages 65-74]
Shalchian, Majid Development of a model based combined Fuzzy-PID controller for idle speed control of internal combustion engine [Volume 38, Issue 38, 2015, Pages 3-16]
Shamekhi Amiri, Sharbanou Investigation on the Effects of Geometrical Specifications of Injection on Performance of a Direct Injection Hydrogen Fueled Engine [Volume 37, Issue 37, 2015, Pages 13-24]
Shams, M. Numerical investigation of cavitation in diesel injector nozzle using two-âfluid modeling [Volume 34, Issue 34, 2014, Pages 41-49]
Sharghi, P. Heat Balance of a Natural Gas Fueled Spark Ignition Engine with a Turbocharger [Volume 20, Issue 20, 2010, Pages 45-58]
Sharghi, P. Experimental and numerical investigation of stress in engine crankshaft [Volume 32, Issue 32, 2013, Pages 29-36]
Sharghi, P. Investigation of diesel fuel and soybean methyl esters emission in high-speed diesel engine [Volume 35, Issue 35, 2014, Pages 31-39]
Sharghi, P. Simulation of piston and ring friction at the motoring condition and investigation effect of combustion and clearance between the piston and cylinder [Volume 39, Issue 39, 2015, Pages 41-48]
Sharghi, Peyman CFD simulation of wall film during fuel injection and combustion in a three-cylinder turbocharged gasoline direct injection engine [Volume 70, Issue 4, 2024, Pages 1-13]
Sharifzadeh, A. Experimental Investigation of the EGR Temperature Effects on the Destruction of the Fuelâs Availability Due to Combustion Processes in IDI Diesel Engine Cylinder [Volume 22, Issue 22, 2011, Pages 62-68]
Sharifzadeh, M. Experimental Investigation of the EGR Temperature Effects on the Destruction of the Fuelâs Availability Due to Combustion Processes in IDI Diesel Engine Cylinder [Volume 22, Issue 22, 2011, Pages 62-68]
Shaterian Alghalandis, V. Introducing an Approach for Feasibility Study of Replacing the Manual Transmission System with CVT System to Reduce the Fuel Consumption [Volume 16, Issue 16, 2009, Pages 52-61]
Shaterian Alghalandis, V. Development of a Dynamic Model and Optimal Control of CVT Transmission System for Minimum Fuel Consumption [Volume 21, Issue 21, 2011, Pages 35-47]
Shaterian Alghalandis, V. Experimental investigation of injector pump type effect on performance âparameters and emissions of âdiesel engine at full load [Volume 34, Issue 34, 2014, Pages 61-70]
Sheikhrezaee, Ahmad Development of an in-cylinder processes model of a CVVT gasoline engine using artificial neural network [Volume 51, Issue 51, 2018, Pages 53-62]
Sheikhzadeh, Ghanbar Ali Numerical analysis of the effect of new matrix network structure technology to enhancement the internal heat transfer of gas turbine blades [Volume 71, Issue 3, 2024, Pages 56-76]
Shekarriz, M. Formation of diesel-water nano-emulsion: Importance, advantages and evaluation of engine performance [Volume 33, Issue 33, 2014, Pages 53-60]
Shervani-Tabar, M.T. Numerical comparison of physical conditions effect on spray behavior of dimethyl ether, biodiesel and diesel fuels [Volume 35, Issue 35, 2014, Pages 17-29]
Sheykhvazayefi, Meysam Experimental study of the diesel injector nozzle sediment effect on fuel spray behavior [Volume 54, Issue 54, 2019, Pages 13-23]
Shirneshan, Alireza Artificial neural network model to predict the performance of a diesel power generator fueled with biodiesel [Volume 42, Issue 42, 2016, Pages 43-50]
Shirneshan, Alireza Numerical Simulation Effect of EHC on CO Emission in Cold-Start Conditions of a Motorcycle Engine [Volume 44, Issue 44, 2016, Pages 43-52]
Shirneshan, Alireza Simulation and investigation of the effect of oil flow rate, electric signal of flow control valve and controller on the performance of a wet clutch [Volume 54, Issue 54, 2019, Pages 65-77]
Shirneshan, Alireza Emission Characteristics of a Diesel Engine fueled with Diesel-biodiesel-JP-4 Blends [Volume 57, Issue 57, 2020, Pages 3-14]
Shirneshan, Alireza Prediction and Comparison of the Effect of N-butanol and Ethanol Addition to the Biodiesel-diesel Fuel Mixture on the Performance and Emissions Characteristics of a Diesel Engine [Volume 64, Issue 64, 2021, Pages 28-40]
Shojaeefard, M.H. A Study on Noise Transmission Loss (TL) Through Duct of Air Intake System of Engine with Porous Insulator Considering Statistical Energy Analysis Method [Volume 19, Issue 19, 2010, Pages 29-37]
Shojaeefard, M.H. Using predictive combustion model in combustion modeling of cooled EGR turbocharged engine [Volume 25, Issue 25, 2012, Pages 57-67]
Shojaeefard, Mohammad Hassan The Thermal Simulation of an Exhaust Valve and its Seat Using Thermal Contact Conductance Obtained from the Inverse Solution [Volume 36, Issue 36, 2014, Pages 27-38]
Shojaeefard, Mohammad Hassan Investigation of the viscosity of CuO–ZnO hybrid nanolubricant for application in internal combustion engines with a MD approach [Volume 72, Issue 3, 2025, Pages 64-84]
Shooshtari, A. The initial estimate of the useful life of the oil in diesel engines using oil analysis [Volume 25, Issue 25, 2012, Pages 45-55]
Shooshtari, A. Complete and partial vibration mode decoupling of national engine about torque roll axis [Volume 40, Issue 40, 2015, Pages 3-12]
Shooshtari, Alireza Optimizing the Shape of Rubber Part of EF7 Engine Mount to Improve its Vibration Behavior [Volume 46, Issue 46, 2017, Pages 49-64]
Siamaki, M. Effect of tumble flap on combustion and performance of NA national engine [Volume 49, Issue 49, 2018, Pages 3-18]
Sina, Naser Simulation of fuel consumption of a hydrogen fuel cell electric vehicle with a thermostat control strategy and variables affecting its fuel consumption in ADVISOR software [Volume 72, Issue 3, 2025, Pages 85-105]
Sohrabi, S. Numerical investigation of cavitation in diesel injector nozzle using two-âfluid modeling [Volume 34, Issue 34, 2014, Pages 41-49]
Soleymani, M. Modeling of traffic conditions impact on fuel consumption and emissions of passenger cars in Arak city [Volume 35, Issue 35, 2014, Pages 53-61]
Solmaz, Hamit Evaluation of the Effects of Equivalence Ratio on the Combustion in an HCCI Engine [Volume 61, Issue 61, 2021, Pages 47-59]
Soltanalizadeh, S Improving identification of combustion engine to use in model-based calibration [Volume 63, Issue 63, 2021, Pages 23-34]
Soltani, Parviz Performance and Emissions of a Tractor engine operating on biodiesel-diesel blends with EGR [Volume 42, Issue 42, 2016, Pages 13-22]
Soltani, Parviz Evaluate the effect of biodiesel and EGR system on diesel engine emissions [Volume 42, Issue 42, 2016, Pages 23-32]
Soltani, R. A New Approach to Flow Network Analysis of an Engine Lubrication System [Volume 18, Issue 18, 2010, Pages 12-19]
Soltani, R. Effects of Nano-Particles on Properties of Engine Oil and its Functionality Rate on Wear Reduction [Volume 24, Issue 24, 2011, Pages 3-12]
Soltanloo, mostafa Failure Analysis of a Exhaust Valve in a Bus Engine [Volume 38, Issue 38, 2015, Pages 27-38]
Souri, Saeed Design and simulation of a hybrid electric vehicle in order to increasing efficiency and reducing pollution [Volume 37, Issue 37, 2015, Pages 35-48]
Souzani, Adib Experimental study of the effect of magnetic flux density on fuel consumption and emissions in diesel engine [Volume 66, Issue 66, 2022, Pages 57-67]
Souzani, Adib Vibration analysis of turbocharger in different clogging conditions of Diesel Particle Filter (DPF) [Volume 70, Issue 1, 2023, Pages 66-90]
T
Tabrizi, A. Investigating the effect of nanocoating on friction loss and abrasion in the piston rings [Volume 53, Issue 53, 2019, Pages 13-22]
Taghizadeh, Mostafa Investigation of torque and power output of power generation system in hybrid electric vehicles with parallel arrangement in driving modes [Volume 64, Issue 64, 2021, Pages 54-66]
Taghizadeh Alisaraei, A. Simulation of vibration for a diesel engine with biodiesel and diesel fuel blends using artificial neural networks [Volume 23, Issue 23, 2011, Pages 22-31]
Taghizadeh-Alisaraei, Ahmad Evaluation of Performance and Vibration of a Diesel Engine Using Ag Nanoparticles Added to Diesel and Biodiesel Fuel Blends [Volume 46, Issue 46, 2017, Pages 15-26]
Tahani, M. A study on side effects of cooling in a new active multi-compartment mount [Volume 29, Issue 29, 2013, Pages 25-38]
Tahani, M. Study on effect of electric/combustion engine on performance of a parallel hybrid vehicle and proposing engine selection algorithm [Volume 31, Issue 31, 2013, Pages 21-31]
Taheri, A. Effect of Crossing Diesel Fleet in Tehran on Black Carbon Air Pollution [Volume 49, Issue 49, 2018, Pages 19-28]
Tahi, P. Effect of starting temperature and belt width on lateral force of timing belt [Volume 48, Issue 48, 2017, Pages 13-18]
Tajdari, Mehdi Effect of fuel injection discharge curve and injection pressure on upgrading power and combustion parameters in HD diesel engine with CFD simulation [Volume 42, Issue 42, 2016, Pages 3-12]
Talebi, A. Optimization of Online induction Sensor for Ferrous Metals Particles Identification in Engine Oil [Volume 53, Issue 53, 2019, Pages 3-12]
Talebi, Farhad Design and analysis of a thermoelectric generator for a heavy-duty vehicle in âreal road test [Volume 68, Issue 68, 2022, Pages 12-22]
Talebi, R. A Study on Noise Transmission Loss (TL) Through Duct of Air Intake System of Engine with Porous Insulator Considering Statistical Energy Analysis Method [Volume 19, Issue 19, 2010, Pages 29-37]
Tale Masouleh, M. Dynamic-Thermodynamic Mathematical Model of Stirling Engine to Improve Efficiency and Power [Volume 23, Issue 23, 2011, Pages 72-85]
Tarahomi, Masoud Optimization of car gearbox conversion ratios based on providing maximum traction in different gears [Volume 66, Issue 66, 2022, Pages 36-45]
Tarahomi, R. Multi-Dimensional Simulation of n-Heptane Combustion under HCCI Engine Condition Using Detailed Chemical Kinetics [Volume 22, Issue 22, 2011, Pages 3-12]
Tavakoli Hashjin, T. Prediction Oil Parameter of Connecting Rod Small End Bearing of EF7 Engine by Using Artificial Neural Network by Simulation in AVL Excite Software [Volume 20, Issue 20, 2010, Pages 22-29]
Tavakoli Hashjin, T. Simulation of vibration for a diesel engine with biodiesel and diesel fuel blends using artificial neural networks [Volume 23, Issue 23, 2011, Pages 22-31]
Teimouri, Mohsen Experimental study of combustion noise level in LTC engine [Volume 51, Issue 51, 2018, Pages 43-52]
Teymoori, Mohammad Mahdi Fuel consumption optimization of a series hybrid electric vehicle utilizing fuzzy logic control [Volume 68, Issue 68, 2022, Pages 23-30]
Toosi, A. Effects of piston bowl geometry on combustion and emissions characteristics of a natural gas/diesel RCCI engine [Volume 40, Issue 40, 2015, Pages 59-70]
Tor Savadkouhi, L. Theoretical and Experimental Analysis of OM314 Diesel Engine Combustion and Performance Characteristics Fueled with DME [Volume 14, Issue 14, 2009, Pages 71-78]
Torshizian, M.R. Stress intensity factor in single cracked gears made of steel and functionally graded materials in vehicle gearbox [Volume 29, Issue 29, 2013, Pages 47-56]
V
Vajdi, Mohammad An experimental study of determining friction force between ring and cylinder by measuring piston movement [Volume 71, Issue 2, 2024, Pages 40-54]
Valentino, G. Fluid Dynamics Investigation of a GDI Fuel Spray by Particle Image Velocimetry [Volume 14, Issue 14, 2009, Pages 19-26]
Varmazyar, M. Research on modification of cooling passage for a 4-cylinder turbo-charged SI engine with precise cooling view point [Volume 41, Issue 41, 2016, Pages 31-39]
Vatankhahan, Farshad Comparison between revolution sensor by using PVDF sensor in XU7 engine and vibration energy harvesting [Volume 44, Issue 44, 2016, Pages 3-18]
Vaziri, Bahram Sensitivity analysis for objectives of power, efficiency, heat loss, and working fluid cost based on input parameters in the Stirling engine [Volume 70, Issue 2, 2023, Pages 1-21]
Voshtani, S. Controlling natural gas combustion timing in HCCI engine with synthetic gas enrichment using a chemical kinetic model [Volume 32, Issue 32, 2013, Pages 13-20]
Vossoughi, G. Nonlinear Oxygen Sensor Output Voltage Estimation in a Gasoline Engine Using NARX Model [Volume 22, Issue 22, 2011, Pages 13-20]
Vossoughi, G.R. Steady-state modeling of a turbocharger in gasoline engines [Volume 26, Issue 26, 2012, Pages 21-30]
W
Wan Ghazali, Wan Nor Maawa Investigation of Blended Palm Biodiesel-Diesel Fuel Properties with Water Emulsification [Volume 57, Issue 57, 2020, Pages 65-74]
Y
Yaghoubi, M. Two Phase Flow Simulation for Subcooled Nucleat Boiling Heat Transfer Calculation in Water Jacket of Diesel Engine [Volume 22, Issue 22, 2011, Pages 50-61]
Yaghoubi, M. Simulation of heat transfer considering boiling phenomenon in cooling passage of turbo-charged national engine [Volume 29, Issue 29, 2013, Pages 3-14]
Yaqubi, Sadegh Designing Nonlinear Digital Controller for Switching Non Affine Process of Spark Ignition Engine Catalyst Warm-Up [Volume 65, Issue 65, 2022, Pages 42-59]
Yari, Mortaza Study on the effect of using reformed biogas as a low reactivity fuel in a dual-fuel engine (RCCI) [Volume 59, Issue 59, 2020, Pages 73-93]
Yazdani Jo, Alireza Automatic intelligent inspection system for crankshaft grade detection based on machine vision and deep learning [Volume 71, Issue 4, 2025, Pages 33-43]
Yazdanparast, S. K. Oil Quality Monitoring in Gasoline Spark Ignition Engine Using Oil Dielectric Measurement [Volume 53, Issue 53, 2019, Pages 45-54]
Yazdi, Mohammad Hossein Convolutional transformer approach for engine spark plug fault diagnosis using acoustic signal [Volume 70, Issue 4, 2024, Pages 56-68]
Yeganeh Moghadam, A.M. Performance Evaluation of a Samand Vehicle with Internal Combustion Engine System and Hybrid Electric-Fuel Cell System [Volume 24, Issue 24, 2011, Pages 51-64]
Yekani, Seyyed Kazem Measuring the mass of fuel injected into the engine cycle by introducing a gas pressure fueling system [(Articles in Press)]
Yekani, S. K The Effect Of Burned Residual Gases On Gasoline-NG Dual-Fuel Engine Combustion Performance With Skip-Fire Technique [Volume 63, Issue 63, 2021, Pages 3-11]
Yosri, Mohammad Reza The Thermal Simulation of an Exhaust Valve and its Seat Using Thermal Contact Conductance Obtained from the Inverse Solution [Volume 36, Issue 36, 2014, Pages 27-38]
Yousefzadeh, A. Developing a multi-zone thermo-kinetic model to investigate effects of using DME-methane blend in an HCCI engine [Volume 32, Issue 32, 2013, Pages 37-47]
Yousefzadeh, A. An experimental study of pre-main injection strategy to optimize TDI diesel engine [Volume 41, Issue 41, 2016, Pages 55-62]
Yousefzadeh, A. Principle of valves timing optimization in D87 diesel to premixed natural gas engine conversion [Volume 49, Issue 49, 2018, Pages 65-76]
Yousefzadeh, M. Creation of ceramic-metal joint in new generation of high heat resistant engines by brazing [Volume 27, Issue 27, 2012, Pages 59-65]
Z
Zabetian Toroghi, M. Combustion Simulation of Natural Gas in Homogeneous Charge Compression Ignition (HCCI) Engines and Analysis of Effect of Engine Operating Conditions on Combustion Initiation [Volume 15, Issue 15, 2009, Pages 1-10]
Zahedi, F. Low cycle fatigue analysis of magnesium alloy cylinder head based on plastic strain energy approach [Volume 27, Issue 27, 2012, Pages 3-10]
Zakeri, A. Thermal analysis of multiple layers steel(MLS) cylinder head gasket via test [Volume 48, Issue 48, 2017, Pages 19-26]
Zakeri, A. Thermal Analysis of Turbocharger Steel Gasket via Experimental Test [Volume 53, Issue 53, 2019, Pages 33-44]
Zakeri, Ehsan Conceptual and experimental study of an Atkinson cycle engine of a Series-Parallel hybrid electric vehicle [Volume 70, Issue 4, 2024, Pages 69-80]
Zakeri, Mohammad The effects of shear force on size and morphology of the dendrite arm spacing of A356-Al2O3 nano composites [Volume 67, Issue 67, 2022, Pages 24-29]
Zandi, A. Numerical investigation of cavitation in diesel injector nozzle using two-âfluid modeling [Volume 34, Issue 34, 2014, Pages 41-49]
Zarafshan, Payam Modeling and simulation of PEM Used for Automotive Applications [Volume 65, Issue 65, 2022, Pages 75-87]
Zare, Mostafa Reduction of emissions and fuel consumption of diesel engine by using common rail fuel injection and aftertreatment systems [Volume 68, Issue 68, 2022, Pages 3-11]
Zare, Mostafa Reduction of emissions and fuel consumption of diesel engines by ECU program recalibration and after-treatment system [Volume 71, Issue 2, 2024, Pages 18-29]
Zarei, Hadi Experimental study of the effect of magnetic flux density on fuel consumption and emissions in diesel engine [Volume 66, Issue 66, 2022, Pages 57-67]
Zarenejad Ashkezari, Abbas Optimization of fuel consumption and emissions in diesel engines by using of artificial neural network and ant colony algorithm with intake VVT and fuel injection approach [Volume 43, Issue 43, 2016, Pages 13-30]
Zarenezhad Ashkezari, Abbas Experimental Investigation of the Combination of Ethanol-Biodiesel, Ethanol-Diesel, and Ethanol-Biodiesel-Diesel Emulsion Blends on Performance and Emissions of Direct Injection Diesel Engines [Volume 66, Issue 66, 2022, Pages 3-21]
Zarinchang, J. Fluid Dynamics Investigation of a GDI Fuel Spray by Particle Image Velocimetry [Volume 14, Issue 14, 2009, Pages 19-26]
Zehni, A. Optimizing exhaust noise and back pressure of exhaust system in turbo-charged three-liter diesel engine [Volume 35, Issue 35, 2014, Pages 63-70]
Zeinali, S Comprehensive Investigation on the Effect of the EGR Components on n-heptane HCCI Combustion [Volume 63, Issue 63, 2021, Pages 49-60]
Ziabasharhagh, M. Numerical Simulation of Direct Injection Engine with using Porous Media [Volume 23, Issue 23, 2011, Pages 45-58]
Ziabasharhagh, M. A new technique for determination of geometry characteristics, mass flow rate and discharge coefficient of a direct gas injection nozzle [Volume 29, Issue 29, 2013, Pages 57-66]
